Introduces wave parameters and types, the principle of superposition and its consequences: interference (coherent sources, path-difference conditions), stationary waves on strings and in organ pipes (harmonics), a microwave standing-wave experiment, diffraction (ripple tank), beats, wave intensity, and the Doppler effect with its applications.
7.3 Interference and Its Types · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.6 MB
Superposition of two waves having the same frequency and travelling in the same direction results in phenomenon called interference.
Figure 7.5(a): An experimental setup to observe interference of sound waves (original drawing after the textbook's Figure 7.5(a)).
Figure 7.5 (b): Interference of sound waves (original drawing after the textbook's Figure 7.5 (b)).
An experimental set up to observe interference effect of sound waves is shown in Fig. 7.5(a). Two loud speakers S₁ and S₂ act as two sources of harmonic sound waves of a fixed frequency produced by an Audio Generator (AG). Since the two speakers are driven from the same generator, therefore, they vibrate in phase. Such sources of waves are called coherent sources. A microphone attached to a sensitive Cathode Ray Oscilloscope (CRO) acts as a detector of sound waves. The CRO is a device to display the input signal into waveform on its screen. The microphone is placed at various points, turn by turn, in front of the loud speakers as shown in Fig. 7.5(b).
7.4 Stationary Waves & Their Formation · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
Stationary waves, also known as standing waves, are the waves that oscillate in a fixed position, without moving or propagating. They are formed by the superposition of two waves with the same frequency and amplitude, travelling in opposite directions. The resulting wave pattern remains stationary, with nodes (points of zero amplitude) and antinodes (points of maximum amplitude) at fixed positions. Examples include waves on a string, and sound waves in a pipe. The term "standing wave" describes that the wave pattern remains fixed in space, oscillating between positive and negative values, without moving forward or backward.
Let us consider the superposition of two waves moving along a string in opposite directions. Figures 7.6 (a) and (b) show the profile of two such waves at instants t = 0, T/4, T/2, 3/4 T and T, where T is the time period of the wave. We are interested in finding out the displacements of the points 1, 2, 3, 4, 5, 6 and 7 at these instants as the waves superpose. It is obvious that the points 1, 2, …, 7 are distant λ/4 apart, λ being the wavelength of the waves. We can determine the resultant displacement of these points by applying the principle of superposition.
Figure 7.6 (c) shows the resultant displacement of the points 1, 3, 5 and 7 at the instants t = 0, T/4, T/2, 3T/4 and T. It can be seen that the resultant displacement of these points is always zero. These points of the medium are known as nodes. Here, the distance between two consecutive nodes is λ/2.
7.8 Diffraction of Waves
7.8 Diffraction of Waves · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 69 KB
Diffraction through a slit (PDF page 157): small wavelength, small diffraction; large wavelength, large diffraction (original drawing after the textbook's picture in this box).
Diffraction of waves is the bending of waves around the sharp edges or corners of obstacles or the spreading of waves beyond a barrier. It occurs when a wave encounters a physical barrier or an opening (a slit) that is comparable in size to the wavelength of the wave. The longer the wavelength, the greater the spreading and vice versa.
Diffraction can be observed in various types of waves, including water waves, sound waves, light waves and electromagnetic waves.
Some examples of the phenomenon of diffraction include:
Hearing of sound waves around corners or through door way from where they were generated as sound waves bend around the corners.
Diffraction of X-rays by crystals as the spacing between the regular arrays of atoms is of the order of X-rays wavelength.
Diffraction is a fundamental aspect of wave behaviour and has many practical applications in various fields.
Transverse and Longitudinal Waves · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
Figure 7.3: Main types of waves (original drawing after the textbook's Figure 7.3).
There are two main types of waves which are named as transverse waves and longitudinal waves. A transverse wave is one in which the vibrations of the particles are at right angle to the direction in which the energy of the wave is travelling. Whereas a longitudinal wave is one in which the direction of the vibration of the particles is along or parallel to the the direction in which the energy of the wave is travelling.
The transverse wave and longitudinal wave are illustrated in Figs. 7.3 (a and b), respectively.
7.6 Stationary Waves in Air Columns · Reviewed lesson · version 1 · published 16 Nov 2026
Stationary waves can be set up in other media also, such as air column inside a pipe or tube. A common example of vibrating air column is in the organ pipe.
Tuning Musical Instruments · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.9 MB
Here are some examples of how beats are generated in musical instruments:
Do you know? (PDF page 160): players of string and wind musical instruments (original line drawing after the textbook's picture in this box).
Guitar: When playing two strings with slightly different tunings, beats are created. For example, playing a standard tuned string and a string tuned a few cents higher or lower.
Piano: Playing two keys white and black, adjacent to each other, creates beats.
Violin: When playing two strings with slightly different bow pressures or speeds, beats are generated.
Drums: When two drums with slightly different tunings are played simultaneously, beats are created.
Flute: When playing two notes with slightly different embouchure (lip and facial muscles) positions, beats are generated.
7.7 Experiment Demonstrating Stationary Waves Using Microwaves
7.7 Experiment Demonstrating Stationary Waves Using Microwaves · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.3 MB
Structure of Microwave Oven (PDF page 156): magnetron, metal wave-guide, rotating stirrer, food on turntable, metal box and door window (original drawing after the textbook's picture in this box).
Microwaves are a form of electromagnetic radiations. They are called "micro" waves because their wavelengths are typically of the order of millimetres or centimetres, much shorter than radiowaves. Stationary waves, also known as standing waves, can be produced by microwaves when they are confined to a specific region or cavity such as wave guides or resonant chambers. In these structures, microwaves can bounce back and forth, creating a standing wave pattern with nodes and antinodes. It occurs when the microwave frequency matches the resonant frequency of the cavity.
The stationary waves can be created using microwaves by the following simple method as shown in Fig. 7.10.
Figure 7.10: Experimental setup for stationary waves using microwave (original drawing after the textbook's Figure 7.10).
The Ripple Tank
The Ripple Tank · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.9 MB
Figure 7.11: A ripple tank (original drawing after the textbook's Figure 7.11).
Fig. 7.11 shows a ripple tank. It is a very useful apparatus not only to generate water waves, but also to demonstrate wave properties (such as reflection, diffraction and refraction).
Small gap, increased diffraction; large gap, decreased diffraction (original drawing after the diagrams printed with the textbook's Figure 7.11).
Ripple tank contains water, vibrator (e.g. a motorized oscillating needle), obstacles (e.g. a small rectangular block or a semicircular barrier) and gap widths of different sizes. It creates a series of concentric circles or parallel waves using the vibrator. An obstacle is placed for creating a gap with a specific width. The experiment can be repeated with different gap widths.
Organ pipe
Organ pipe · Reviewed lesson · version 1 · published 16 Nov 2026
An organ pipe is a wind instrument in which sound is produced, due to setting up of stationary waves in air column. It consists of a hollow long tube with both ends open or with one end open and the other closed. The relationship between the incident wave and the reflected wave depends upon whether the reflecting end of the pipe is open or closed.
(i)If the reflecting end is open, the air molecules have complete freedom of motion and this behaves as an antinode.
(ii)If the reflecting end is closed, then it behaves as a node because the movement of the molecules is restricted.
Types of Waves · Reviewed lesson · version 1 · published 16 Nov 2026
Waves have various forms, each with unique characteristics. A brief detail of different types of waves is given below:
1. Mechanical Waves
These waves require a physical medium (solid, liquid, or gas) to propagate. Examples are water waves (ocean, lake, or pond ripples), sound waves (audible vibrations in air, water, or solids), seismic waves (earthquakes), etc.
2. Electromagnetic Waves
They do not require a medium to propagate and therefore, can travel through vacuum. Examples are radiowaves (wireless communication), Microwaves (cooking and heating), Infrared waves (IR or heat radiation), Visible light (sunlight, lamp light), Ultraviolet waves (UV radiation), X-rays (medical imaging), Gamma rays (high-energy radiation), etc.
3. Quantum Waves
Quantum waves are associated with particles like electrons and photons. Examples are matter waves/particle waves (electron waves in atoms) or de-Broglie waves, photon waves (light quanta), etc.
4. Surface Waves
Surface waves propagate along surfaces or interfaces between two mediums. Examples are ocean surface waves (wind-driven waves), seismic surface waves, etc.
Applications of the Principle of Superposition
Applications of the Principle of Superposition · Reviewed lesson · version 1 · published 16 Nov 2026
By applying the principle of superposition of waves, noise-cancelling headphones effectively eliminate unwanted noise, providing a more immersive and peaceful listening experience.
The headphones contain one or more microphones that capture ambient noise (like background chatter or engine rumble or any environmental noise).
The microphone sends the sound signals to an amplifier and a processing unit in the headphones.
The processing unit generates an "anti-noise" signal, which is the exact opposite of the ambient noise (in terms of amplitude and phase).
The anti-noise signal is then played through the headphones, along with the desired audio (like music or voice).
When the anti-noise signal meets the ambient noise, the two waves cancel each other out resulting in a much quieter listening experience.
Though the above example is an oversimplification of the situation, as noise-canceling headphones use complex algorithms and multiple microphones to achieve optimal noise cancellation, the basic principle of superposition remains a fundamental concept in understanding how they work.
Harmonics · Reviewed lesson · version 1 · published 16 Nov 2026
In the above example, the set of all the possible standing waves, having frequencies f₁, 2f₁, 3f₁, …, nf₁, are called harmonics of the system. The lowest or fundamental frequency of all the harmonics is called the fundamental or first harmonic. Subsequent frequencies are called as second harmonic, third harmonic, etc.
Example 7.3
A stationary wave is established in a string which is 120 cm long and fixed at both ends. The string vibrates in four segments; at a frequency of 120 Hz. Determine its wavelength and the fundamental frequency?
Solution: l = 120 cm = (120/100) m = 1.2 m
n = 4
f₄ = 120 Hz
f₁ = ?
λ = ?
(i)As the string vibrates in four segments and the distance between two consecutive nodes is λ/2, so the wavelength of the string is:
l = n (λₙ/2)
λₙ = 2l/n
λ₄ = (2 × 1.2)/4
λ₄ = 0.6 m
(ii)
7.12 Applications of Doppler Effect
7.12 Applications of Doppler Effect · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.5 MB
Figure 7.13: A frequency shift is used in a radar to detect the motion of an aeroplane: (a) plane approaching, (b) plane receding (original drawing after the textbook's Figure 7.13).
Doppler effect is also applicable to electromagnetic waves. One of its important applications is the radar system, which uses radio waves to determine the elevation and speed of an aeroplane. RADAR (RAdio Detection And Ranging) is a device, which transmits and receives radio waves. If an aeroplane approaches towards the radar, then the wavelength of the wave reflected from aeroplane would be shorter and if it moves away, then the wavelength would be larger as shown in Fig. 7.13 (a) & Fig. 7.13 (b), respectively. Similarly, speed of satellites moving around the Earth can also be determined by the same principle.
SONAR is an acronym derived from "Sound Navigation And Ranging". It is the general name for sonic or ultrasonic underwater echo-ranging and echo-sounding system. Sonar is the name of a technique for detecting the presence of objects under water by acoustical echo. In Sonar, "Doppler detection" relies upon the relative speed of the target and the detector to provide an indication of the target speed. It employs the Doppler effect, in which an apparent change in frequency occurs when the source and the observer are in relative motion to one another. Its known military applications include the detection and location of submarines, control of antisubmarine weapons, mine hunting and depth measurement of sea.
(c) String Plucked at an Arbitrary Point
(c) String Plucked at an Arbitrary Point · Reviewed lesson · version 1 · published 16 Nov 2026
Let the string resonates in n number of loops with (n + 1) nodes and n antinodes. Thus, we can say that if the string is made to vibrate in n loops, the frequency of stationary waves set up on the string will be:
fn=n(2ℓv)
swipefₙ = n (v/2l)
Destructive Interference
Destructive Interference · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
At points P₂ and P₄, a compression meets a rarefaction, so that they cancel each other's effect according to the principle of superposition. The resultant displacement becomes zero, as shown in Fig. 7.5(d).
The path difference ΔS between the waves at points P₂ and P₄, is
ΔS=S2P2−S1P2
swipeΔS = S₂P₂ − S₁P₂
7.2 Principle of Superposition of Waves
7.2 Principle of Superposition of Waves · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.5 MB
If a particle of the medium is simultaneously acted upon by two waves, then the resultant displacement of the particle is the algebraic sum of their individual displacements. This is called principle of superposition.
In other words, the displacements of the individual waves are added together to form a new wave pattern as shown in Fig. 7.4 (a and b), respectively.
(i)If two waves, which overlap each other, have same phase, their resultant displacement will be:
y=y1+y2
swipey = y₁ + y₂
7.9 Beats
7.9 Beats · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.3 MB
When two waves of slightly different frequencies, travelling in the same direction overlap each other then there is a periodic variation of sound between maximum and minimum loudness which is called as beats.
Tuning forks give out pure notes (single frequency). If two tuning forks A and B of the same frequency say 32 Hz are sounded separately, they will give out pure notes. If they are sounded simultaneously, it will be difficult to differentiate the notes of one tuning fork from that of the other. The sound waves of the two will be superposed on each other and will be heard by the human ear as a single pure note.
If the tuning fork B is loaded with some wax or plasticene, its frequency will be lowered slightly, say it becomes 28 Hz. If now the two tuning forks are sounded together, a note of alternately increasing and decreasing intensity will be heard. This note is called beat note or a beat which is due to interference between the sound waves from tuning forks A and B.
Figure 7.12: Formation of beats (original drawing after the textbook's Figure 7.12).
Fig. 7.12 (a) shows the waveform of the note emitted from a tuning fork A. Similarly, Fig. 7.12(b) shows the waveform of the note emitted by tuning fork B. When both the tuning forks A and B are sounded together, the resultant waveform is shown in Fig. 7.12(c). It shows how do the beat note occur. At some instant X, the displacement of the two waves is in the same direction. The resultant displacement is large and a loud sound is heard.
Case 1: [When source of sound moves towards the stationary observer]
Case 1: [When source of sound moves towards the stationary observer] · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
When the source moves towards the stationary observer C with velocity uₛ then waves are compressed and their wavelength is decreased as shown in Fig. 7.13 (c). In this case, the waves are compressed by an amount given as
Δλ=fus
swipeΔλ = uₛ/f
7.1 Waves
7.1 Waves · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.5 MB
We are well familiar with various types of waves such as water waves in the ocean and circular ripples formed on a still pool of water by rain drops. When a musician plucks a guitar string, sound waves are generated in air which reach our ear and produces sensation of music. The vast energy of the Sun, millions kilometres away, is transferred to the Earth by light waves. In this chapter, we will discuss, formation, propagation and applications of different types of waves.
(a) String Plucked at its Middle Point
(a) String Plucked at its Middle Point · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 60 KB
Figure 7.7(a): First mode of vibration (original drawing after the textbook's Figure 7.7(a)).
If the string is plucked at its middle point, two transverse waves will originate from this point. One of them will move towards the left end of the string and the other towards the right end. When these waves reach the two clamped ends, they are reflected back thus giving rise to stationary waves. As the two ends of the string are clamped, no motion will take place there. So, nodes will be formed at the two ends and one mode of vibration of the string will be as shown in Fig. 7.7(a) with the two ends as nodes with one antinode in between. Visually, the string seems to vibrate in one loop. As the distance between two consecutive nodes is one half of the wavelength of the waves set up in the string, so in this mode of vibration, the length l of the string is
ℓ=λ1/2
swipel = λ₁/2
Case (1): Modes of vibrations in an organ pipe open at both ends
Case (1): Modes of vibrations in an organ pipe open at both ends · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 83 KB
Let us consider an organ pipe of length l which is open at both ends. As at the open end, an air molecule has complete freedom of motion so it acts as antinode as shown in Fig. 7.8. In this figure, longitudinal waves set up inside the pipe have been represented by transverse curved lines which represent the displacement and amplitude of vibration of air particles at various points along the axis of pipe.
(a) Fundamental mode of vibration
Figure 7.8: Stationary longitudinal waves in a pipe open at both ends (original drawing after the textbook's Figure 7.8).
In this case, as shown in Fig. 7.8 (a), there is only one node N at the middle of the pipe. As both ends of pipe are open, there are two antinodes at both the ends. If λ₁ is the wavelength of sound, then
ℓ=4λ1+4λ1
swipel = λ₁/4 + λ₁/4
(b) String Plucked at Quarter Length
(b) String Plucked at Quarter Length · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 71 KB
Figure 7.7(b): Second mode of vibration (original drawing after the textbook's Figure 7.7(b)).
If the same string is plucked from one quarter of its length, again stationary waves will be set up with nodes and antinodes as shown in Fig. 7.7 (b). Note that now the string vibrates in two loops. This particular configuration of nodes and antinodes has developed because the string was plucked from the position of an antinode. As the distance between two consecutive nodes is half the wavelength, so the length l of string is equal to the wavelength of the waves set up in this mode. If λ₂ is the measure of wavelength of these waves, then,
ℓ=2λ2+2λ2
swipel = λ₂/2 + λ₂/2
Beat Frequency (f_beat)
Beat Frequency (f_beat) · Reviewed lesson · version 1 · published 16 Nov 2026
The difference between the frequencies of the two waves is termed as beat frequency f_beat. The time interval between the two successive loud sound is T = t₂ − t₁. Therefore,
fbeat=T1
swipef_beat = 1/T
7.10 Intensity (I) of a Wave
7.10 Intensity (I) of a Wave · Reviewed lesson · version 1 · published 16 Nov 2026
Intensity is defined as the amount of energy transmitted per unit area per unit time in the direction of propagation of progressive wave. It is a measure of the power of a wave and is usually denoted by the symbol "I". It is measured in units of watts per square meter (W m⁻²).
A progressive wave or travelling wave is one that travels through a medium in a consistent direction and transferring energy from one point to another. It is a wave that propagates or moves forward, as opposed to a stationary or standing wave. Examples of progressive waves include water waves, sound waves, light waves etc.
By definition, the intensity of a wave, is
I=A×tE
swipeI = E/(A × t)
7.11 Doppler Effect
7.11 Doppler Effect · Reviewed lesson · version 1 · published 16 Nov 2026
The apparent change in the frequency (or pitch) of waves due to the relative motion between the source and observer (listener) is called Doppler Effect.
This effect was first observed by John Doppler while he was observing the frequency of light emitted from a star. In some cases, the frequency of emitted light was found to be slightly different from that emitted from a similar source on the Earth. He found that the change of frequency of light depends upon motion of star relative to Earth.
This effect can be observed with sound waves also. For example, when an observer is standing on a railway platform, the pitch of whistle of an engine coming towards the platform appears to become higher to an observer standing on the platform. However, the pitch of whistle of an engine going away from the platform appears to become lower to an observer standing on the platform.
Consider a source of sound S at rest which emits sound waves having wavelength λ. Let speed of the sound for a stationary observer (i.e., listener) is v then the number of waves received by observer in one second i.e., frequency f is
f=λv
swipef = v/λ
Case 2: [When source of sound moves away from the stationary observer]
Case 2: [When source of sound moves away from the stationary observer] · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.3 MB
When the source moves away from the stationary observer D with velocity uₛ then waves are expanded and their wavelength is increased as shown by Fig. 7.13 (d). In this case, the waves expanded by an amount
λD=fus
swipeλ_D = uₛ/f
Constructive Interference
Constructive Interference · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 98 KB
Interference pattern produced by a thin soap film illuminated by white light (original drawing after the photograph printed in the textbook).
At points P₁, P₃ and P₅, we find that a compression meets a compression and a rarefaction meets a rarefaction. So, the displacement of two waves are added up at these points according to the principle of superposition and a large resultant displacement is seen on the CRO screen (Fig. 7.5-c).
Figure 7.5(c): Constructive Interference: Large displacement is displayed on the CRO screen (original drawing after the textbook's Figure 7.5(c)).
Figure 7.5(d): Destructive Interference: Zero displacement is displayed on the CRO screen (original drawing after the textbook's Figure 7.5(d)).
Case (2): Modes of vibration in an organ pipe closed at one end
Case (2): Modes of vibration in an organ pipe closed at one end · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
Let us consider an organ pipe of length l which is closed at one end. Then at the closed end, we get a node while at the open end, we get an antinode as shown in the Fig. 7.9.
(a) Fundamental mode of vibration:
Fundamental mode of vibration has one node and one antinode as shown in Fig. 7.9 (a). If λ₁ is the wavelength of fundamental mode then length of the pipe is:
ℓ=4λ1
swipel = λ₁/4
Figure 7.6: Stationary / Standing waves (original drawing after the textbook's Figure 7.6).
Figure 7.6 (d) shows the resultant displacement of the points 2, 4 and 6 at the instants t = 0, T/4, T/2, 3T/4 and T. The figure shows that these points are moving with an amplitude which is the sum of the amplitudes of the component waves represented by arrows. These points are known as antinodes. They are situated midway between the nodes and are λ/2 apart. The distance between a node and the next antinode is λ/4. Such a pattern of nodes and antinodes is known as a stationary or standing wave.
Energy in a wave transfers because of the motion of the particles of the medium. The nodes always remain at rest, so energy cannot flow past these points. Hence, energy remains “standing” in the medium between nodes, although it alternates between potential and kinetic forms at the antinodes. When the antinodes are all at their extreme displacements, the energy stored is wholly potential and when they are simultaneously passing through their equilibrium positions, the energy is wholly kinetic.
Organ: When playing two pipes with slightly different tunings, beats are created.
Synthesizer: Generating two oscillators with slightly different frequencies creates beats.
In each of these examples, the slight difference in frequency between the two sound sources creates a periodic increase and decrease in amplitude, resulting in a "beat" or pulsation effect.
Musicians often use beats intentionally to create interesting rhythmic effects, add texture, or produce a sense of tension and release. However, in some cases, beats can be unwanted and may require adjustments to tuning, pitch, or playing technique to minimize their impact.
Example 7.7
Two tuning forks exhibit beats at a beat frequency of 3 Hz. The frequency of one fork is 256 Hz. Its frequency is then lowered slightly by adding a bit of wax to one of its prongs. The two forks then exhibit a beat frequency of 1 Hz. Determine the frequency of the second tuning fork.
Solution: Frequency of first tuning fork = f₁ = 256 Hz
Beat frequency before loading = 3 Hz
Beat frequency after loading = 1 Hz
Frequency of second tuning fork = f₂ = ?
As f₁ − f₂ = ±n
Then f₂ = f₁ ± n
Putting values, we have
f₂ = 256 ± 3
Either f₂ = 256 + 3; or f₂ = 256 − 3
f₂ = 259 Hz or 253 Hz
Let us consider 259 Hz as correct answer (i.e., frequency of second tuning fork). When first fork is loaded with wax, the frequency of first fork must fall below 256 Hz i.e., 255, 254 and thus the number of beats produced per second will increase and will be greater than 3 beats. Since the number of beats per second decreases on loading first fork is one, therefore 259 Hz is not correct frequency of second tuning fork.
Portrait printed beside the note on the invention of tuning forks (original drawing after the picture printed in the textbook).
The experiment setup consists of a microwave source (transmitter), a probe detector and a metal reflector (a metallic plate for the reflection of microwave). Three of the mentioned are placed in line.
The waves coming out of microwave source are moving towards the metal plate and then reflected back. The reflected wave and incident wave superpose and create a stationary wave pattern. This can be detected by a probe detector placed between transmitter and metallic plate. The intensity of the signal can be observed by the detector. You can move the plate or detector to observe antinode and node. By finding the distance from one antinode to the next antinode, the wavelength of stationary wave can be found.
Diffraction of white light is shown by a fine diffraction grating.
Diffraction of white light is shown by a fine diffraction grating (original drawing after the photograph printed in the textbook).
It is observed that when the gap width is small compared to the wavelength, diffraction is significant and the waves bend around the obstacle, creating a semicircular pattern. As the gap width increases relative to wavelength, diffraction decreases and the waves pass through the gap with less bending.
This experiment demonstrates the qualitative effect of gap width on diffraction in a ripple tank, illustrating how the relationship between gap width and wavelength affects wave behaviour.
Example 7.6
In a ripple tank, a wave generator produces 500 pulses in 10 s. Find the frequency of the pulses produced?
Solution: n = 500 pulses
t = 10 s
f = ?
∵ T = t/n = 10 s/500 = 1/50 s
∵ f = 1/T = 1/(1/50 s) = 50 s⁻¹
Compact discs: their fine rulings act as a diffraction grating (original drawing after the photograph printed in the textbook).
There are two main types of waves which are named as transverse waves and longitudinal waves. A transverse wave is one in which the vibrations of the particles are at right angle to the direction in which the energy of the wave is travelling. Whereas a longitudinal wave is one in which the direction of the vibration of the particles is along or parallel to the the direction in which the energy of the wave is travelling.
The transverse wave and longitudinal wave are illustrated in Figs. 7.3 (a and b), respectively.
In Astronomy, astronomers use the Doppler effect to calculate the speeds of distant stars and galaxies. By comparing the line spectrum of light from the star with light from a laboratory source, the Doppler shift of the star's light can be measured. Then, the speed of the star can be calculated.
Figure 7.14: (a) stationary star, (b) star receding, (c) star approaching (original drawing after the textbook's Figure 7.14).
(i)Stars moving away from the Earth show a red shift as shown in Fig. 7.14(b). The emitted waves have a longer wavelength than if the star had been at rest. So, the spectrum is shifted towards longer wavelength, i.e., towards the red end of the spectrum. Astronomers have also discovered that all the distant galaxies are moving away from us and by measuring their red shifts, they have estimated their speeds.
(ii)Stars moving towards the Earth show a blue shift as shown in Fig. 7.14(c). This is because the wavelength of light emitted by the star are shorter than if the star had been at rest. So, the spectrum is shifted towards shorter wavelength, i.e., to the blue end of the spectrum.
Another important application of the Doppler shift using electromagnetic waves is the radar speed trap. Microwaves are emitted from a transmitter in short bursts. Each burst is reflected off by any car in the path of microwaves in between sending out bursts. The transmitter is open to detect reflected microwaves. If the reflection is caused by a moving obstacle, the reflected microwaves are Doppler shifted. By measuring the Doppler shift, the speed at which the car moves is calculated by computer programme.
Satellite Navigation uses Doppler shift to determine satellite velocity and position, enabling accurate location tracking.
Satellite Communication also uses Doppler shift compensation ensuring stable communication signals.
Doppler radar detects wind velocity and precipitation patterns. Doppler shift helps measure Earth's surface velocity and deformation.
Doppler echocardiography measures blood flow velocity and detects cardiac abnormalities, such as valve stenosis or regurgitation. Doppler echocardiography optimizes pacemaker settings.
Doppler ultrasound measures blood flow and calculates cardiac output. Doppler ultrasound detects vascular stenosis or occlusion.
Example 7.12
The wavelength of one of its lines of the absorption spectrum of a faint galaxy is identified as Ca-α line found to be 478 nm. The wavelength of same line is observed and measured as 397 nm in the laboratory.
(a)Is the galaxy moving towards or away from the Earth?
(b)Compute the speed of the galaxy relative to the Earth.
Solution:
Laboratory measured original wavelength λ = 397 nm = 397 × 10⁻⁹ m
Changed or Apparent wavelength λ′ = 478 nm = 478 × 10⁻⁹ m
It is clear that as the string vibrates in more than one loop, its frequency f goes on increasing and the wavelength λ gets correspondingly shorter. However, the product of the frequency f and wavelength λ is always equal to v, the speed of waves.
The above discussion clearly establishes that;
The stationary waves have a discrete set of frequencies f₁, 2f₁, 3f₁, …, nf₁ which is known as harmonic series. The lowest characteristic frequency of vibration is the fundamental frequency f₁ corresponds to the first harmonic. The frequency f₂ = 2f₁ corresponds to the second harmonic and so on.
In other words, quantum jumps in frequency exist between the resonance frequencies. This phenomenon is known as the Quantization of Frequencies. It means fₙ = nf₁ where n = 1, 2, 3, … (Integral multiples). The stationary waves can be set up on the string only with the frequencies of harmonic series determined by the tension, length and mass per unit length of the string. Waves which are not in harmonic series are quickly damped out.
The frequency of a string on a musical instrument can be changed either by varying the tension or by changing the length. For example, the tension in guitar and violin strings is varied by tightening the pegs on the neck of the instrument. Once the instrument is tuned, the musicians vary the frequency by moving their fingers along the neck, thereby changing the length of the vibrating portion of the string.
Therefore, the condition for destructive interference can be written as:
ΔS=(2n+1)λ/2where n=0,±1,±2,±3,…
swipeΔS = (2n + 1) λ/2 where n = 0, ±1, ±2, ±3, ……
Example 7.1
Two speakers are arranged as shown in the figure. The distance between them is 3.0 m and they emit a constant tone of 344 Hz. A microphone P is moved along a line parallel to and 4.0 m from the line connecting the two speakers. It is found that tone of maximum loudness is heard and displayed on the CRO when microphone is on the centre of the line and directly opposite to each speaker. Calculate the speed of sound.
Solution:
Distance between speakers S₁S₂ = 3.0 m
Tone frequency f = 344 Hz
Distance between speakers and line of motion of P S₁P = 4.0 m
Speed of sound v = ?
For tone of maximum loudness or the condition for constructive interference, the path difference must be 0, ±1λ, ±2λ, ±3λ, …
At middle point 'O' the path difference between two sound waves is zero (S₁O = S₂O), thus at that point 'O' constructive interference takes place.
For the next point P of constructive interference, the path difference between waves should be λ. So, λ = path difference = S₂P₁ − S₁P₁
Now, we calculate values of S₂P₁ from right angle triangle S₁S₂P₁
This is the path difference for constructive interference.
As v = fλ
Putting the values, we have v = 344 × 1 = 344 m s⁻¹
Example 7.1 (PDF page 145): two speakers 3.0 m apart and a microphone moved along a line 4.0 m away (original drawing after the textbook's picture in this box).
Example 7.2
The wavelength of a signal from a radio transmitter is 1500 m and the frequency is 200 kHz. What is the wavelength for a transmitter operating at 1000 kHz and with what speed the radio waves travel?
Solution:
λ₁ = 1500 m = 1.5 × 10³ m, f₁ = 200 KHz = 2.0 × 10⁵ Hz
f₂ = 1000 KHz = 1 × 10⁶ Hz, λ₂ = ?, v = ?, As v = fλ
Since, the speed of both the signals is same, so
v = f₁λ₁
v = 2.0 × 10⁵ × 1500
v = 3.0 × 10⁸ m s⁻¹
Also v = f₂λ₂
λ₂ = v/f₂
λ₂ = (3 × 10⁸ m s⁻¹)/(1 × 10⁶ Hz)
Monochromatic Light: sodium chloride in a flame gives out pure yellow light (original drawing after the photograph printed in the textbook).
Figure 7.4 (a): Superposition of two waves of the same frequency which are exactly in phase (original drawing after the textbook's Figure 7.4 (a)).
where y₁ = amplitude of wave 1, y₂ = amplitude of wave 2 and y = resultant amplitude.
Particularly, if y₁ = y₂, then resultant displacement will be:
y=2y1,ory=2y2
swipey = 2y₁, or y = 2y₂
(ii)If two waves, which cross each other, have opposite phase, their resultant displacement will be:
y=y1+(−y2)
swipey = y₁ + (−y₂)
y=y1−y2
swipey = y₁ − y₂
Particularly, if y₁ = y₂, then resultant displacement will be y = 0.
Figure 7.4 (b): Superposition of two waves of the same frequency which are exactly out of phase (original drawing after the textbook's Figure 7.4 (b)).
Thus, if a particle of a medium is simultaneously acted upon by n waves such that its displacement due to each of the individual n waves be y₁, y₂, ……, yₙ, then the resultant displacement y of the particle, under the simultaneous action of these n waves is the algebraic sum of all the displacements, i.e.,
y=y1+y2+⋯+yn
swipey = y₁ + y₂ + … + yₙ
This is called principle of superposition of waves. Mathematically, this can also be represented as:
y(x,t)=y1(x,t)+y2(x,t)+⋯+yn(x,t)
swipey(x,t) = y₁(x,t) + y₂(x,t) + … + yₙ(x,t)
where y(x,t) is the resultant wave, whereas y₁(x,t), y₂(x,t), ……, yₙ(x,t) are the individual waves.
In the context of waves, y(x,t) represents the wave function or wave displacement at a given point x and time t. It describes the shape of the wave and its evolution over time.
The principle of superposition applies to linear waves or small
Principle of superposition of waves leads to many interesting phenomena:
An interference pattern formed with white light (original drawing after the photograph printed in the textbook).
(i)Two waves having same frequency and travelling in the same direction (Interference).
(ii)Two waves of slightly different frequencies and travelling in the same direction (Beats).
(iii)Two waves of equal frequency travelling in opposite direction (Stationary waves).
After 1/4 s the displacement of the wave due to one tuning fork is opposite to the displacement of the wave due to the other tuning fork resulting in minimum displacement at Y, hence, faint sound or no sound is heard.
Another 1/4 s later, the displacements are again in the same direction and a loud sound is heard again at Z.
As the difference of the frequency of the two tuning forks is also 4 Hz so, we find that the number of beats per second is equal to the difference between the frequencies of the tuning forks.
fA=32Hz,fB=28Hz,fA>fB
swipef_A = 32 Hz, f_B = 28 Hz, f_A > f_B
No. of beats=fA−fB=32Hz−28Hz=4
swipeNo. of beats = f_A − f_B = 32 Hz − 28 Hz = 4
However, when the difference between the frequencies of the two sounds is more than 10 Hz, it becomes difficult to recognize the beats.
Pictorial Comparison (PDF page 159): longitudinal wave (sound) and transverse wave (visible light) (original drawing after the textbook's picture in this box).
One can use beats to tune a string instrument, such as piano or violin, by beating a note against a note of known frequency. The string can then be adjusted to the desired frequency by tightening or loosening it until no beats are heard.
Figure 7.12: A source moving with velocity uₛ towards a stationary observer C and away from stationary observer D respectively. Observer C hears an increased and observer D hears a decreased frequency (original drawing after the textbook's Figure 7.12).
The compression of the waves is due to the fact that same number of waves are contained in a shorter space depending upon the velocity of the source. The wavelength observed by the observer C is then
λC=λ−Δλ
swipeλ_C = λ − Δλ
orλC=fv−fus
swipeor λ_C = v/f − uₛ/f
λC=fv−us
swipeλ_C = (v − uₛ)/f
Here Δλ is the decrease in wavelength in one second and is called Doppler shift.
Thus, the number of waves received by observer C in one second (i.e., changed or apparent frequency) is
fC=λCv
swipef_C = v/λ_C
Putting the value of λ_C, we have
fC=[(v−us)/fv]
swipef_C = [v/((v − uₛ)/f)]
fC=[v−usv]f
swipef_C = [v/(v − uₛ)] f
Asv−usv>1
swipeAs v/(v − uₛ) > 1
ThereforefC>f
swipeTherefore f_C > f
Thus, the apparent frequency of sound heard by the observer increases which in turn will increase the pitch of sound.
Figure 7.1: Representing a travelling disturbance (ripple) (original drawing after the textbook's Figure 7.1).
A wave is a regular disturbance or variation that carries energy, which spreads out from the source. For example, energy is transferred from the Sun to the Earth in the form of light waves called electromagnetic waves, can even travel through vacuum. However, in a medium, energy is transferred due to the regular and repeated disturbances that travel through the medium, making its particles to move up and down or back and forth (to and fro). Imagine a stone thrown into a pond of water (Fig. 7.1).
The stone produces a disturbance (ripple) that travels through the water (medium).
The water particles move up and down at their own places, creating a repeating pattern known as wave that spreads out.
Figure 7.2: Graphical description of a wave (original drawing after the textbook's Figure 7.2).
The displacement of a particle of a wave is its distance in a specified direction from its rest / equilibrium position. If the displacement is plotted along the y-axis and the time in the direction of energy travel along the x-axis, we get a waveform as shown in Fig. 7.2.
The waves can be described by the following parameters:
Interesting Information (PDF page 140): Wavy shape of water wave in 3D (original drawing after the textbook's picture in this box).
Amplitude (A): The maximum displacement of the wave (or particles of the medium) from its equilibrium position.
Frequency (f): The number of oscillations/vibrations or cycles per second.
Wavelength (λ): The distance between two consecutive similar points on the wave that are in phase.
Period (T): The time taken by the wave to complete one oscillation or cycle. it is the reciprocal of the frequency T = 1/f.
Speed (v): The speed at which the wave travels. If a wave crest moves one wavelength λ in one period of oscillation T the speed v is given by
v=Tλ
swipev = λ/T
as 1/T = f we have
v=fλ(7.1)
swipev = fλ (7.1)
Phase (θ): The relative position of a point on the wave at a given time.
where λ₁ is the wavelength of the waves set up in this mode. The speed v of the waves in the string depends upon the tension F of the string and m, the mass per unit length of the string. It is independent of the point from where string is plucked to generate wave. It is given by
v=mF(7.3)
swipev = √(F/m) (7.3)
Knowing the speed v and wavelength λ₁, the frequency f₁ of the waves is
f1=λ1v=2ℓv
swipef₁ = v/λ₁ = v/2l
Substituting the value of v, to get
f1=2ℓ1mF(7.4)
swipef₁ = (1/2l) √(F/m) (7.4)
Thus, in the first mode of vibration shown in Fig. 7.7 (a), waves of frequency f₁ only will be set up in the given string.
If f₁ is the frequency of sound, then the velocity of sound is:
v=f1λ1
swipev = f₁λ₁
f1=v/λ1
swipef₁ = v/λ₁
Putting value of λ₁, we have
f1=v/2ℓ(7.8)
swipef₁ = v/2l (7.8)
This frequency is called fundamental frequency or first harmonic.
(b) Second mode of vibration
If there are three antinodes and two nodes, frequency will be twice that of fundamental frequency. It is second mode of vibration as shown in Fig. 7.8 (b). In this case, there are three antinodes and two nodes.
If λ₂ is the wavelength of sound then,
ℓ=4λ2+2λ2+4λ2
swipel = λ₂/4 + λ₂/2 + λ₂/4
ℓ=(1+2+1)4λ2
swipel = (1+2+1) λ₂/4
orλ2=ℓ
swipeor λ₂ = l
If f₂ is the frequency of sound, then speed v of sound becomes:
v=f2λ2
swipev = f₂λ₂
orf2=λ2v
swipeor f₂ = v/λ₂
Putting the value of λ₂, we have
f2=ℓv
swipef₂ = v/l
orf2=2f1(∵2ℓv=f1)
swipeor f₂ = 2f₁ (∵ v/2l = f₁)
(c) nth mode of vibration
Similarly, frequency for air column vibrating in n loops is:
fn=n(v/2ℓ)
swipefₙ = n(v/2l)
fn=nf1
swipefₙ = nf₁
and wavelength is
λn=2ℓ/n(7.9)
swipeλₙ = 2l/n (7.9)
where n = 1, 2, 3, 4, 5, ………
So, the longitudinal stationary waves have a discrete set of frequencies f₁, 2f₁, 3f₁, …, nf₁, which is known as harmonic series. The frequency f₁ is known as fundamental frequency and the others are called harmonics.
Comparison of Eq. (7.4) with Eq. (7.1) shows that the wavelength in this case is half of that in the first case. Eq. (7.2) shows that the speed of the waves depends on tension and mass per unit length of the string, it is independent of the point where the string is plucked. So, speed v remains the same in both cases.
If f₂ is frequency of vibration of string in its second mode, then
f2=λ2v
swipef₂ = v/λ₂
Since,
λ2=ℓ
swipeλ₂ = l
f2=ℓv
swipef₂ = v/l
Multiplying and dividing by 2, we have
f2=2ℓ2v
swipef₂ = 2v/2l
We know that
f1=2ℓv
swipef₁ = v/2l
So
f2=2f1
swipef₂ = 2f₁
Thus, when the string vibrates in two loops, its frequency becomes double than when it vibrates in one loop.
We know that in mechanical waves, such as sound waves, water waves, or waves on a vibrating string, energy is stored as kinetic energy and potential energy of the medium's particles. How much energy is stored depends upon the displacement (amplitude) of the particles from the mean position. Therefore, the intensity I of waves is proportional to the square of the amplitude A, i.e.,
I∝A2
swipeI ∝ A²
orI=kA2(7.13)
swipeor I = kA² (7.13)
Here 'k' is the constant of proportionality and depends upon the physical properties of the wave and the medium.
Example 7.8
(a)A wave has an intensity of 0.5 W m⁻² at a distance of 3.0 m from the source. What is the power of the wave?
(b)Two progressive waves have intensities of 0.5 W m⁻² and 0.25 W m⁻². Find total intensities of two waves.
Solution:
(a)I = 0.5 W m⁻²
r = 3.0 m
P = ?
∵ I = P/A
∵ I = P/(4πr²)
Putting the values, 0.5 = P/(4 × 3.14(3.0)²)
P = 0.5 × 113.04
P = 56.52 W
(b)I₁ = 0.5 W m⁻²
I₂ = 0.25 W m⁻²
I = ?
I = I₁ + I₂
I = 0.5 + 0.25
I = 0.75 W m⁻²
Example 7.9
A speaker is emitting sound waves with a power of 50 watts. If the sound waves are spreading out evenly in all directions and the intensity of the sound waves is measured at a distance of 5 m from the speaker, what is the intensity of the sound waves if the area of the sphere (the surface area of a sphere) at that distance is approximately 314 m²?
The expansion of the waves is due to the fact that same number of waves are now contained in a large distance. The wavelength observed by the observed D is then
λD=λ+Δλ
swipeλ_D = λ + Δλ
where Δλ is the increase in wavelength in one second and is called Doppler shift.
Thus, the number of waves received by observer D in one second (i.e., changed or apparent frequency) is:
fD=v/λD
swipef_D = v/λ_D
Putting the value of λ_D, we have
fD=[(v+us)/fv]
swipef_D = [v/((v + uₛ)/f)]
fD=[(v+us)v]f
swipef_D = [v/(v + uₛ)] f
Asv+usv<1
swipeAs v/(v + uₛ) < 1
Therefore,fD<f
swipeTherefore, f_D < f
Thus, the apparent frequency of sound heard by the observer decreases which in turn will decrease the pitch of sound.
Info Corner: Hearing Ranges
Organisms
Frequencies in Hz
Dolphin
150 – 150,000
Bat
1000 – 120,000
Cat
60 – 70,000
Dog
15 – 50,000
Human
20 – 20,000
swipe
Do You Know? (PDF page 165): an aircraft below, at and above the speed of sound, forming a shockwave (original drawing after the textbook's picture in this box).
Example 7.10
Two trucks P and Q travelling along a motorway in the same direction. The loading truck P travels at a steady speed of 12 m s⁻¹, the other truck Q, travelling at a steady speed of 20 m s⁻¹, sound its horn to emit a steady note which P's driver estimate, has a frequency of 830 Hz. What frequency does Q's own driver hear?
(Speed of sound = 340 m s⁻¹)
Solution:
u_P = 12 m s⁻¹
u_Q = 20 m s⁻¹
v = 340 m s⁻¹
f_P = 830 Hz
f_Q = ?
Speed of Q relative to P = uₛ = u_Q − u_P = 20 − 12 = 8 m s⁻¹
∵ f = (v/(v − uₛ)) f′
∴ f_P = (v/(v − uₛ)) f_Q
Putting the value, we have
830 = (340/(340 − 8)) f_Q
830 = (340/332) f_Q
or f_Q = (830 × 332)/340
f_Q = 810.47 Hz
Example 7.10 (PDF page 166): truck Q, the source at 20 m s⁻¹, behind truck P, the listener at 12 m s⁻¹ (original drawing after the textbook's picture in this box).
Example 7.11
A train sounds its horn before it sets off from the station and an observer waiting on the platform estimates its frequency at 1200 Hz. The train then moves off and accelerates steadily. Fifty seconds after departure, the driver sounds the horn again and the platform observer estimates the frequency at 1140 Hz. Calculate the train speed 50 s after departure. How far from the station is the train after 50 s.
(Speed of sound = 340 m s⁻¹)
Solution:
Original frequency of horn = f = 1200 Hz
Apparent frequency = f′ = 1140 Hz
Speed of sound = v = 340 m s⁻¹
Time = t = 50 s
Speed of source (i.e., train) = uₛ = ?
Distance covered by the train = S = ?
(i)f′ = (v/(v + uₛ)) f
Putting the values, we have
1140 = (340/(340 + uₛ)) × 1200
340 + uₛ = (340 × 1200)/1140
uₛ = 357.89 − 340
uₛ = 17.89 m s⁻¹
(ii)S = v_av t
S = ((vᵢ + v_f)/2) t
S = ((0 + 17.89)/2) 50
Bats navigate and find food by echo location (original drawing after the photograph printed in the textbook).
From Fig. 7.5 (b), we find that the path difference ΔS between the waves at the point P₁, is,
ΔS=S2P1−S1P1
swipeΔS = S₂P₁ − S₁P₁
ΔS=421λ−321λ=λ
swipeΔS = 4½λ − 3½λ = λ
Similarly, at points P₃ and P₅, path difference is zero and −λ, respectively. Here, λ is the wavelength which is the distance between any two successive solid or dashed lines.
Therefore, the condition for constructive interference can be written as
Figure 7.9: Stationary longitudinal waves in a pipe closed at one end. Only odd harmonics are present (original drawing after the textbook's Figure 7.9).
So, the speed v becomes
v=f1λ1
swipev = f₁λ₁
f1=λ1v
swipef₁ = v/λ₁
f1=4ℓv(∵λ1=4ℓ)
swipef₁ = v/4l (∵ λ₁ = 4l)
The frequency f₁ is called fundamental frequency.
(b) Second Mode of Vibration:
A Scientific Fact (PDF page 153): the wavering, sheet-like air jet from the flue-slit of an organ pipe (original drawing after the textbook's picture in this box).
Second mode of vibration contains two nodes and two anti-nodes as shown in Fig. 7.9 (b).
If λ₃ is the wavelength, then length of the pipe is:
ℓ=4λ3+2λ3
swipel = λ₃/4 + λ₃/2
ℓ=43λ3
swipel = (3/4) λ₃
λ3=34ℓ(7.11)
swipeλ₃ = 4l/3 (7.11)
f3=λ3v
swipef₃ = v/λ₃
Putting value of λ₃, we have v = f₃λ₃
f3=4ℓ/3v
swipef₃ = v/(4l/3)
orf3=4ℓ3v
swipeor f₃ = 3v/4l
sof3=3f1[∵4ℓv=f1]
swipeso f₃ = 3f₁ [∵ v/4l = f₁]
This is called second harmonic.
(c) nth mode of vibration
If air column vibration in n loops, then frequency fₙ is:
fn=n(4ℓv)
swipefₙ = n (v/4l)
fn=nf1
swipefₙ = nf₁
and the wavelength λₙ is:
λn=n4ℓ(7.12)where n=1,3,5,…
swipeλₙ = 4l/n (7.12) where n = 1, 3, 5, …
By studying both cases, we conclude that the pipe which is open at both ends is richer in harmonics than that of closed at one end.
Example 7.4
An organ pipe has a length of 50 cm. Find the frequency of its fundamental note and the next harmonic, when it is:
(a)open at both ends
(b)closed at one end
(speed of sound = 350 m s⁻¹)
Solution: l = 50 cm = (50/100) m = 0.5 m
v = 350 m s⁻¹
a)When pipe is open at both ends:
Fundamental frequency f₁ = ?
Next harmonic frequency f₂ = ?
The frequency for nth harmonic in an open organ pipe is:
fₙ = n (v/2l) when n = 1, 2, 3, ………
so the fundamental frequency is,
f₁ = (1 × 350)/(2 × 0.5) put n = 1
f₁ = 350 Hz
Next harmonic frequency i.e., n = 2 is:
f₂ = 2v/2l
f₂ = v/l = 350/0.5
f₂ = 700 Hz
b)When pipe is closed at one end:
Fundamental frequency f₁ = ?
Next harmonic frequency f₃ = ?
When the pipe is closed at one end then frequency for nth harmonic is:
fₙ = n (v/4l) when n = 1, 3, 5, 7, ………
So fundamental frequency is:
f₁ = (1 × 350)/(4 × 0.5) put n = 1
f₁ = 175 Hz
Next harmonic frequency i.e., n = 3 is:
f₃ = 3v/4l
f₃ = (3 × 350)/(4 × 0.5)
f₃ = 525 Hz
Example 7.5
A church organ consists of pipes, each open at one end, of different lengths. The minimum length is 30 mm and the longest is 4 m. Calculate the frequency range of the fundamental notes. (speed of sound = 340 m s⁻¹)
Solution: l_min = 30 mm = (30/1000) m = 30 × 10⁻³ m
l_max = 4 m
v = 340 m s⁻¹
Frequency range = ?
For an organ pipe open at one end only:
fₙ = nv/4l
(i)Minimum length
For fundamental frequency, put n = 1
f₁,max = nv/4l_min
f₁,max = (1 × 340)/(4 × 30 × 10⁻³)
f₁,max = 2833.33 Hz
(ii)Maximum length:
For fundamental frequency, put n = 1
f₁,min = nv/4l_max
f₁,min = (1 × 340)/(4 × 4)
f₁,min = 21.25 Hz
So, the fundamental frequency range is approximately from 21 Hz to 2833 Hz.