Class 12 · Physics · Chapter 17 (Contents page: 5)
Alternating CurrentAlternating Current
Sinusoidal AC characterised by peak, average, rms and phase; behaviour of R, L, C (reactance, phasors) combined into impedance for RC, RL, RLC series and parallel circuits with resonance; rectification and smoothing; self and mutual induction and energy in an inductor.
17.14 Rectification · Reviewed lesson · version 1 · published 16 Nov 2026
Rectification is the process of converting alternating current into direct current.
Diodes allow current to flow in one direction (forward bias) but block it in the opposite direction (reverse bias). Rectification is of two types, half wave rectification and full wave rectification. Rectification is commonly used in electronic devices that require a stable DC power source, such as computers and smartphones, as most household and commercial power is AC.
17.7 Choke · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
A choke is often modeled as a series RL-circuit, consisting of a resistor R, having very small value of resistance, in series with an inductor L, of quite large inductance X_L = 2πf L, as shown in Fig.17.7(e). The inductance L of the choke coil is also very high due to the high permeability of iron core on which choke coil is wound. As the resistance R of a choke coil is negligibly small, therefore, the power factor (cosθ) of the choke coil is almost zero. Thus, the phase difference θ between the current and voltage for a choke coil is nearly equal to 90°. So practically, no power is dissipated as heat by a choke coil. Also choke is used to block high frequency AC while allowing DC and low frequency AC to pass. Choke coils are used to filter out high frequency AC noise from electronic circuits, ensuring a cleaner DC output. They are essential in switch-mode power supplies, helping to regulate voltage and filter out switching noise.
Figure 17.7 (e): A choke (original drawing after the photograph printed as the textbook's Figure 17.7 (e)).
Choke coils prevent unwanted RF signals from leaking out of circuits, protecting other sensitive components. Chokes in fluorescent lights generate transient voltages across the tube, making it conducive to the breakdown voltage of the gas inside. Choke coils can limit the rate of current changes in circuits, preventing damage to insulation from sudden surges.
Vector Representation of an Alternating Quantity · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 91 KB
An alternating quantity can be represented by an anticlockwise rotating vector if it satisfies the conditions: (i) Its length on a certain scale represents the peak value or rms value of alternating quantity. (ii) It is in horizontal position at the instant. When the alternating quantity is zero and is increasing positively (iii) The angular frequency of the rotating vector is same as the angular frequency of alternating quantity.
Figure 17.5 (d), (e): (d) Graphical representation showing voltage V leads current I by pi/2; (e) vector diagram OI and OV showing V leads I by 90 degrees or pi/2 rad (original drawing after the textbook's Figure 17.5 (d), (e)).
Fig.17.5 (d) shows an alternating voltage waveform leading the current wave form by 90° or π / 2 rad. In Fig.17.5(e), vector OI represents peak or rms value of current which is taken as reference quantity. Similarly, OV represents peak or rms value of alternating voltage, which is leading the current by π/2 rad or 90°. Both vectors are rotating in anticlockwise direction with angular frequency.
17.13 AC Through RLC-Parallel Circuit · Reviewed lesson · version 1 · published 16 Nov 2026
A RLC-parallel circuit is one where the resistor, inductor and capacitor are connected in parallel to each other with an AC source as shown in Fig.17.12 (a). The parallel arrangement affects the overall impedance and current distribution in the circuit, making it distinct from its series counterpart.
Half-Wave Rectifier · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.4 MB
In a half-wave rectification, an AC signal is converted into pulsating direct current DC by passing one half-cycle of waveform and blocking the other half. In Fig.17.13, alternating voltage of period T called input voltage is supplied to a diode D which is connected in series with a load resistance R_L. The working of half-wave rectifier is based on the fact that the diode allows the current flow only in one direction. Thus, it converts the AC signal into DC signal. Figure 17.13 shows the circuit of half-wave rectification and it is working showing graphically its input and output wave forms.
Figure 17.13: Working of a half-wave rectifier, showing graphically its input and output wave forms (original drawing after the textbook's Figure 17.13).
For your information: a circuit board view of half-wave rectifier with its different components (original drawing after the photograph printed in the textbook's box).
Diode as a Rectifier
Diode as a Rectifier · Reviewed lesson · version 1 · published 16 Nov 2026
A diode allows large current to flow when forward biased. However, the current through a reverse biased diode is practically zero. It is due to this important property of the diode that it can be used for rectification i.e., to convert alternating current into unidirectional current or direct current.
17.4 AC Circuits · Reviewed lesson · version 1 · published 16 Nov 2026
The basic circuit element in a DC circuit is a resistor R which controls the current or voltage and the relation between them is given by Ohm's law (V = IR). But the basic circuit elements in AC circuit are resistor R, inductor L and capacitor C. These elements control the current and voltage through the circuit. The AC circuits with these components are discussed below:
Power dissipation in an inductor · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
The average power dissipated in a pure inductor is zero. This is because the inductor does not consume power in the traditional sense, as it stores energy in the magnetic field and returns it to the source during demagnetisation. The instantaneous power in the inductive circuit is zero and the average power dissipated per cycle is also zero. This behaviour is due to the phase difference between the voltage and current in an AC circuit, which is 90°. Therefore, the average power dissipated in a pure inductor is zero. Since inductor does not consume energy, it is used for controlling AC without consuming energy.
Example 17.4
A 400 mH coil of negligible resistance is connected to an AC circuit in which a current having its rms value of 6 mA is flowing. Find out the value of rms voltage across the coil if its frequency is 1 kHz.
Solution
Inductance of the coil L = 400 mH = 400 × 10⁻³ H
and Iᵣₘₛ = 6 mA = 6 × 10⁻³ A
Frequency f = 1 kHz = 1000 Hz
Full-Wave Rectification
Full-Wave Rectification · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.4 MB
Figure 17.15 (a): Full-wave bridge rectifier circuit showing 4 diode network with load resistance (original drawing after the textbook's Figure 17.15 (a)).
Rectification during which both halves of alternating input voltage are converted into unidirectional current through a resistance is called full-wave rectification. Full-wave rectification is achieved by a bridge rectifier in which four individual rectifying diodes are connected in a closed loop “bridge” configuration to produce the desired output. The single secondary winding is connected to one side of the diode bridge network and the load to the other side. The four diodes labelled diodes D₁ to D₄ are arranged in “series pairs” with only two diodes conducting current during each half-cycle as shown in Fig.17.15(a)
The Positive Half-cycle: We know that diode conducts only when it is forward bias. During the positive half-cycle of the supply i.e., during the time 0 → T/2, the terminal A of the bridge is positive w.r.t. its other terminal B. Now the diodes D₁ and D₂ become forward biased and conduct in series while diodes D₃ and D₄ are reverse biased and the current flows through the load resistance R as shown in Fig.17.15 (b)
Power dissipation in RL-Series circuit
Power dissipation in RL-Series circuit · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
Power consumed in RL- series circuit is primarily due to the resistor, as the inductor stores energy but ideally does not dissipate it. The power consumed by the resistor is given by the formula:
P=I2R=VIcosθ
swipeP = I²R = VI cos θ
17.2 Relation Between Mean Power and Maximum Power for an Alternating Current
17.2 Relation Between Mean Power and Maximum Power for an Alternating Current · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 1.3 MB
An alternating current is a current that periodically reverses direction, causing the voltage and current to fluctuate sinusoidally. A resistive load is one that does not store energy (like a capacitor or inductor) and simply dissipates energy as heat.
P=VI(17.5)
swipeP = VI (17.5)
17.12 Navigating AC Through RLC-Series Circuit
17.12 Navigating AC Through RLC-Series Circuit · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.3 MB
Figure 17.11 (a), (b): (a) RLC-series circuit with its AC source phasor diagram; (b) the impedance vector diagram of RLC-series circuit (original drawing after the textbook's Figure 17.11 (a), (b)).
Consider a RLC-series circuit having an alternating voltage source with variable frequency as shown in Fig.17.11(a). The impedance diagram of RLC-series circuit is shown in Fig.17.11(b) in which inductive reactance X_L = ω L and capacitive reactance X_C = 1 /ω C are directed opposite to each other.
The impedance of the RLC-series circuit is:
Z=R2+(XL−XC)2(17.24)
swipeZ = √(R² + (X_L − X_C)²) (17.24)
17.10 AC Through RC-Series Circuit
17.10 AC Through RC-Series Circuit · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
Consider a network of resistance R and a capacitor C connected in series by an alternating voltage source V as shown in Fig.17.9 (a). As R and C are in series, so same current would flow through each of them. The potential difference V across the resistance R would be Iᵣₘₛ R and it would be in phase with the current. The vector diagram of the voltage and current is shown in Fig.17.9 (b). Taking the current as reference, potential difference V_R = Iᵣₘₛ R across the resistance is represented by a line along the current line because potential drop Iᵣₘₛ R is in phase with current. The potential difference across the capacitor will be:
VC=IrmsXC=ωCIrms
swipeV_C = IᵣₘₛX_C = Iᵣₘₛ/ωC
17.16 Self Induction
17.16 Self Induction · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
Consider a circuit in which a coil is connected in series with a battery, a switch and a rheostat as shown in Fig.17.18. If we move the rheostat quickly, the primary current through the coil will change. The magnetic flux through the coil will also change, which finally induces an emf in the coil itself.
Figure 17.18: A coil showing production of induced current and induced emf in itself (original drawing after the textbook's Figure 17.18).
Let φ represents flux passing through one loop of the coil. The flux passing through the coil of N turns would be Nφ. As this flux φ is proportional to the magnetic field produced which is in turn proportional to the current I, therefore,
Nϕ∝I
swipeNφ ∝ I
Energy Stored in an Inductor
Energy Stored in an Inductor · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
Figure 17.19: Circuit designed to calculate energy stored in an inductor (original drawing after the textbook's Figure 17.19).
Consider a coil connected to a battery and a switch in series as shown in Fig.17.19. When the switch is turned ON, voltage is applied across the ends of coil and current increases from zero to maximum value. Due to change of current, an emf is induced, which is opposite to that of battery. Work is done by battery to move charges against the induced emf.
Work done by battery in moving a small charge Δq is given by
W=ΔqεL(17.34)
swipeW = Δq ε_L (17.34)
17.17 Mutual Induction
17.17 Mutual Induction · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
Consider two coils close to each other as shown in Fig. (17.20). One coil connected with a battery through a switch S and a rheostat, is called Primary coil and the other one connected to the galvanometer is called Secondary coil. If the current in the primary is changed by varying the resistance of the rheostat, the magnetic flux in the surrounding region changes. Since the secondary coil is in magnetic field of the primary, the changing flux also links with the secondary. This causes an induced emf in the secondary.
Figure 17.20: Circuit diagram to find Mutual induction between two coils (original drawing after the textbook's Figure 17.20).
According to Faraday's law, the emf induced in the secondary coil εₛ is proportional to the rate of change of flux Δφₛ/Δt passing through it and is given by
εs=−NsΔtΔϕs(17.39)
swipeεₛ = −Nₛ Δφₛ/Δt (17.39)
Average or Mean Value of AC Waveform
Average or Mean Value of AC Waveform · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
Figure 17.2: Average value of alternating voltage (original drawing after the textbook's Figure 17.2).
If we calculate the average of a complete sine wave over a full cycle (0 to 2π), the result is zero (Fig. 17.2). This happens because the positive half-cycle and the negative half-cycle are mirror images of each other. They cancel out perfectly. That is not very useful. So, when we talk about the average value of an AC waveform, we usually mean the average over one half-cycle (0 to π).
The average value is used in situations involving rectification. When an AC signal passes through a rectifier (such as in a power supply), the output is a pulsating DC signal. The average of this pulsating DC is what matters for many applications. For a full-wave rectified sine wave, the average values of current and voltage are given by
Iav=0.637IoandVav=0.637Vo
swipeIₐᵥ = 0.637 Iₒ and Vₐᵥ = 0.637 Vₒ
17.6 AC Through Inductor
17.6 AC Through Inductor · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
An inductor, also called a coil, or choke is a passive two terminal electrical component having a large value of self -inductance and negligible resistance that stores energy in a magnetic field when electric current flows through it. The inductor is used to slow down current surges or spikes by temporarily storing energy in an electromagnetic field and then releasing it back into the circuit.
Suppose an inductor of inductance L is connected with an AC source of frequency f with a negligible resistance as shown in Fig.17.7 (a). Suppose the current is:
I=Iosinωt(17.13)
swipeI = Iₒ sin ωt (17.13)
Full-Wave Bridge Rectifier with Single Smoothing Capacitor
Full-Wave Bridge Rectifier with Single Smoothing Capacitor · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
In AC to DC conversion, smoothing filters are used to reduce the ripple voltage after rectification. When AC is rectified, the output is pulsating DC, which is not suitable for most electronic devices. Smoothing filters help to produce a more stable DC voltage by filtering the AC components (ripples).They are of different types. In capacitor filter, a capacitor is connected in parallel with the load. It charges when the rectified voltage increases and discharges when the voltage decreases, thereby smoothing the output.
Smoothing or reservoir capacitors connected in parallel with the load across the output of the full-wave bridge rectifier circuit, increase the average DC output level even higher as the capacitor acts like a storage device as shown in Fig.17.17. The smoothing capacitor converts the full-wave rippled output of the rectifier into a more smooth DC output voltage. We can see the effect it has on the rectified output waveform with different values of smoothing capacitor installed.
Figure 17.17: The smoothing capacitor converts the full-wave rippled output of the rectifier into a more smooth DC output voltage (original drawing after the textbook's Figure 17.17).
17.9 Impedance
17.9 Impedance · Reviewed lesson · version 1 · published 16 Nov 2026
In AC circuits, the opposition to current flow is called impedance denoted by Z, which includes both resistance R and reactance X. The resistance R is the opposition to current flow due to resistors. Reactance is the opposition to current flow due to capacitors (capacitive reactance X_C) and inductors (inductive reactance X_L). A pure resistive circuit has only resistance R and no reactance.
It is the ratio of the rms value of the voltage to the rms value of the current. Thus,
Z=IrmsVrms(17.20)
swipeZ = Vᵣₘₛ/Iᵣₘₛ (17.20)
17.1 Alternating Current and its Characteristics
17.1 Alternating Current and its Characteristics · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 77 KB
An alternating current AC means a sinusoidally varying current which can be represented by time dependent sine or cosine functions. The emf of an AC generator is given by the following equation, for voltage:
V=Vosinωt(17.1)
swipeV = Vₒ sin ωt (17.1)
17.11 AC Through RL-Series Circuit
17.11 AC Through RL-Series Circuit · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
Consider an AC circuit containing a resistor R and inductor L connected in series with an AC source V as shown in Fig.17.10(a). As R and L are in series, therefore, same current I flows through both R and L.
I=Iosinθ
swipeI = Iₒ sin θ
Phase Lag and Phase Lead
Phase Lag and Phase Lead · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
Referring to the Figs.17.5 (b) and 17.5(c), at t = 0, the angle θ is also 0°, the value of the phase angle θ at t equals to zero is called the initial phase of AC quantity. Thus, according to equations:
V=VosinθandI=Iosinθ(17.9)
swipeV = Vₒ sin θ and I = Iₒ sin θ (17.9)
17.5 AC Through a Resistor
17.5 AC Through a Resistor · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.2 MB
A resistor R connected with an AC source is shown in Fig.17.6 (a). The instantaneous voltage V is given as:
V=Vosinωt(17.10)
swipeV = Vₒ sin ωt (17.10)
17.3 Phase of A.C.
17.3 Phase of A.C. · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 59 KB
The angle θ which specifies the instantaneous value of the alternating voltage or current is called the phase. The instantaneous values of voltage and current are given by
V=Vosinωt
swipeV = Vₒ sin ωt
orV=Vosinθ
swipeor V = Vₒ sin θ
Root-mean-square (rms) or Effective Value of Current and Voltage:
Root-mean-square (rms) or Effective Value of Current and Voltage · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
Root-mean- square (rms) values of current, or voltage, are a useful way of comparing alternating current, or voltage, to its equivalent direct current, or voltage. The rms values represent the direct current, or voltage, values that will produce the same heating effect, or power dissipation as the alternating current or voltage. The rms value of an alternating current is defined as:
The value of a constant current that produces the same power in a resistor as the alternating current.
Irms=2IoorIrms=0.707Io(17.3)
swipeIᵣₘₛ = Iₒ/√2 or Iᵣₘₛ = 0.707 Iₒ (17.3)
Key Properties of RLC Series Circuit
Key Properties of RLC Series Circuit · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
In essence, the series RLC-circuit is a versatile circuit element that can be designed to exhibit specific behaviour at different frequencies, making it important in various electronic applications.
1.Impedance and Resonance: At resonance impedance, is minimum (Z = R) and at resonance, the resonant frequency can be calculated by using the formula:
fr=2πLC1
swipefᵣ = 1/(2π√LC)
Key Properties of RLC-Parallel Circuit
Key Properties of RLC-Parallel Circuit · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.3 MB
1.Resonance and impedance: A parallel RLC-circuit resonates at X_L = X_C and the impedance is at its maximum value in a way that parallel RLC-circuit behaves like a purely resistive circuit. The impedance of RLC-parallel circuit is given by
Z=(R1)2+(XL1−XC1)21(17.27)
swipeZ = 1/√((1/R)² + (1/X_L − 1/X_C)²) (17.27)
17.8 AC Through a Capacitor
17.8 AC Through a Capacitor · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
Figure 17.8: (a) Capacitor connected with ac voltage source; (b) graphical representation of current and voltage for capacitor; (c) vector representation of current and voltage for a capacitor (original drawing after the textbook's Figure 17.8).
A capacitor does not allow direct current to pass through it because of the presence of an insulating medium between its plates. But alternating current can pass through a capacitor. In electric circuits, a capacitor is a reactive component. Unlike a resistor, a capacitor behaves differently in AC and DC circuits. It is because a capacitor can store energy in the form of electric field, whereas a resistor cannot store electrical energy in any form. Consider an alternating voltage source V is applied to a capacitor of capacitance C as shown in Fig.17.8 (a).
When an alternating voltage is applied across the plates of a capacitor, it is charged in one direction and then in the other as the voltage reverses. The result is that electrons move to and fro around the circuit, connecting the plates, thus, constituting alternating current. The basic relationship between charge q and the voltage V across the plates: q = CV, holds good at every instant. Let V be the applied alternating voltage given by
V=Vosinωt(17.18)
swipeV = Vₒ sin ωt (17.18)
Figure 17.13 (a): A circuit view of a UPS system used in our homes (original drawing after the textbook's Figure 17.13 (a)).
During positive half-cycle of the input alternating voltage i.e., during the interval 0→T/2, the diode D is forward bias, so it offers a very low resistance and current flows through R_L. The flow of current through R_L causes a potential drop across it which varies in accordance with the alternating input (Fig.17.13).
During negative half cycle, during the interval T/2→T, the diode becomes reverse bias and offers a very high résistance, so practically no current flows through R_L and potential drop across it is almost zero (Fig.17.13). The same events repeat during the next cycle and so on. The current across R_L flows in only one direction which means it is direct current. However, this current flows in pulses. The voltage which appears across load resistance R_L is known as output voltage.
Figure 17.15 (b), (c): Full-wave bridge rectifier circuit showing its working during its positive and negative half cycles and also representing graphically its input and output waveforms (original drawing after the textbook's Figure 17.15 (b), (c)).
Figure 17.16 (a): Circuit diagram showing the use of Full wave Bridge Rectifier in mobile charger circuit (original drawing after the textbook's Figure 17.16 (a)).
Figure 17.16 (b): A Compact Full wave Bridge Rectifier used in electronics (original drawing after the textbook's Figure 17.16 (b)).
The Negative Half-cycle: During the negative half cycle of the supply, during the time T/2 → T, terminal A is negative and B is positive. Now the diodes D₃ and D₄ conduct in series, but diodes D₁ and D₂ switch “OFF” as they are now reverse biased. The current flowing through the load is the same direction as before as shown in Fig.17.15 (c). If we take a comparison of Figs.17.15(b) and 17.15(c), it can be seen that direction of current flow through the load resistance is same in both half of the cycle. Thus, both halves of the alternating input voltage send a unidirectional current through load resistance R. The output voltage is not smooth but pulsating. It can be made smooth using a circuit called filter which may consist of capacitors. Mobile phone chargers typically use full-wave bridge rectifier as part of their circuitry. The rectifier converts the alternating current from the wall outlet into direct current, which is necessary to charge the phone's battery.
where I, R and V represents current, resistance, and voltage respectively whereas θ is the phase angle between voltage and current. The factor cos θ is known as power factor. It is to be noted that when we convert DC power P_dc, into AC power P_ac, we have to take an account of a quantity known as inverter efficiency. It usually may be 85 % to 90%. So, we can find AC power from DC power by using the following conversion as:
Pac=(Inverter efficiency)×Pdc
swipeP_ac = (Inverter efficiency) × P_dc
Do you know?: a 1.5 ton air conditioner (original drawing after the picture printed in the textbook's box).
Brain teaser: a solar panel (original drawing after the photograph printed in the textbook's box).
Figure 17.4: Mean power is exactly half the maximum power (original drawing after the textbook's Figure 17.4).
where V is the instantaneous voltage and I is the instantaneous current. The maximum or peak Pₘₐₓ occurs when the current and voltage are at their peak values, Iₒ and Vₒ respectively. Also the mean power Pₘₑₐₙ is the average power over one complete cycle of the AC waveform as shown in Fig.17.4.
For a sinusoidal AC, let Iₒ be the maximum or peak value of the current while voltage Vₒ is the maximum or peak value of the voltage, then the maximum or peak power Pₘₐₓ is given by
Pmax=Io2R(17.6)
swipePₘₐₓ = Iₒ²R (17.6)
Interesting Information: a digital clamp meter for measuring AC and DC (original drawing after the photograph printed in the textbook's box).
Also we have expression for the mean power Pₘₑₐₙ represented by
Pmean=Irms2R(17.7)
swipePₘₑₐₙ = Iᵣₘₛ²R (17.7)
AsIo=2Irms
swipeAs Iₒ = √2 Iᵣₘₛ
so, using Eq. 17.6 becomes:
Pmax=(2Irms)2R=2Irms2R
swipePₘₐₓ = (√2 Iᵣₘₛ)²R = 2Iᵣₘₛ²R
From Eq. 17.7;IRrms2=Pmean,thus
swipeFrom Eq. 17.7; IR²ᵣₘₛ = Pₘₑₐₙ, thus
Pmax=2Pmean
swipePₘₐₓ = 2Pₘₑₐₙ
orPmean=2Pmax(17.8)
swipeor Pₘₑₐₙ = Pₘₐₓ/2 (17.8)
Therefore, it can be concluded that the mean power in a resistive load is half the maximum power for a sinusoidal alternating current or voltage because the instantaneous power in an AC circuit varies over time. While the instantaneous power reaches at maximum value at certain points in the cycle, it spends significant time at zero or lower values, resulting in an average power that is half the peak value.
Example 17.2
An alternating voltage supplied across a resistor of 50 Ω has a voltage of 220 V. Calculate the mean power in kilo watt of the system.
Solution
R = 50 Ω and V = 220 V
We know that;
Pₘₐₓ = V²/R
Putting the values
Pₘₐₓ = (220 V)²/50 Ω = 968 W
As the mean power is half of the maximum (peak) power,
Pₘₑₐₙ = Pₘₐₓ/2 = 968 W/2
Fascinating Fact: human blood sugar converted into electricity (original drawing after the picture printed in the textbook's box).
When frequency is high, then X_L = ωL is much greater than X_C = 1/ω C, and hence the inductance X_L dominates at high frequency, so RLC-series circuit behaves as RL-series circuit.
When frequency is low, then X_C = 1 / ωC is much greater than X_L = ω L, and hence the capacitance X_C dominates at low frequency, hence RLC series circuit behaves as RC series circuit as shown in Fig.17.11(b).
Brain teaser: wiring of a ceiling fan (original drawing after the textbook's picture).
In between these frequencies, there will be a frequency ωᵣ at which X_L = X_C. At this condition, RLC-series circuit behaves as pure resistive R-circuit as shown in Fig.17.11(c).
Figure 17.11 (c), (d): (c) Vector diagram showing that the RLC-series circuit behaves as a pure resistive R-circuit at XL = XC; (d) RLC-series circuit resonance at XL = XC (original drawing after the textbook's Figure 17.11 (c), (d)).
This condition is called resonance. Thus, at resonance, the inductive reactance X_L being equal and opposite to capacitive reactance X_C, cancel each other. The value of resonance frequency fᵣ can be obtained by applying the condition:
Figure 17.9 (a), (b): (a) RC series circuit; (b) voltage phasors of the RC series circuit (original drawing after the textbook's Figure 17.9 (a), (b)).
As this, voltage lags behinds the current by π / 2 rad or 90°, so the line representing the vector Iᵣₘₛ X_C is drawn at right angles to the current line Fig.17.9 (b).
The applied voltage Vᵣₘₛ that will send the current I in the circuit is obtained by resultant of the vectors Iᵣₘₛ R and Iᵣₘₛ/ωC i.e;
Vrms=(VR)2+(VC)2
swipeVᵣₘₛ = √((V_R)² + (V_C)²)
Vrms=(IrmsR)2+(ωCIrms)2
swipeVᵣₘₛ = √((IᵣₘₛR)² + (Iᵣₘₛ/ωC)²)
Vrms=IrmsR2+(ωC1)2
swipeVᵣₘₛ = Iᵣₘₛ √(R² + (1/ωC)²)
Vrms=IrmsR2+(ωC1)2
swipeVᵣₘₛ = Iᵣₘₛ √(R² + (1/ωC)²)
ImpedanceZ=IrmsVrms=R2+(ωC1)2(17.21)
swipeImpedance Z = Vᵣₘₛ/Iᵣₘₛ = √(R² + (1/ωC)²) (17.21)
Equation 17.21 suggests that we can find the impedance of a series AC circuit by vector addition. The resistance R is represented by a horizontal line in the direction of current which is taken as reference. The reactance X_C = 1 / ω C is shown by a line lagging the R-Q line by 90° as shown in Fig.17.9(c). The impedance Z of the circuit is obtained by the vector summation of resistance and reactance. Figure 17.9(c) is known as impedance diagram of the circuit. The angle which the line representing the impedance Z makes with R line gives the phase difference between the voltage and current I in Fig. 17.9(c), the current is leading the voltage applied by the angle θ as shown in Fig.17.9(d) and is given by
Figure 17.9 (c), (d): (c) Impedance diagram of RC series circuit; (d) voltage and current waveform in RC-series circuit (original drawing after the textbook's Figure 17.9 (c), (d)).
The power consumed in RC-series circuit is primarily due to the resistor, as the capacitor only stores energy and does not dissipate it. The power consumed by the resistor can be calculated by using the formula:
P=I2R
swipeP = I²R
orP=VIcosθ(17.22)
swipeor P = VI cos θ (17.22)
where I is the current, R is the resistance, V is the voltage, and θ is the phase angle between voltage and current.
Example 17.6
A resistor of resistance 5 kΩ is connected in series with capacitor of capacitance 5 μF across the AC source of 220 V that has frequency 50 Hz. Calculate the phase angle.
where L is proportionality constant and is called self -inductance of the coil.
The self-inductance L depends upon the following factors:
Number of turns of the coil.
Area of cross-section of the coil.
Core material, by winding the coil around ferromagnetic iron core, the magnetic flux and hence inductance can be increased significantly relative to that for an air core.
By Faraday's law, the emf induced in the coil is given by
εL=−NΔtΔϕ(17.30)
swipeε_L = −N Δφ/Δt (17.30)
εL=−ΔtΔ(Nϕ)
swipeε_L = −Δ(Nφ)/Δt
Using Eq. (17.28);εL=−ΔtΔ(LI)
swipeUsing Eq. (17.28); ε_L = −Δ(LI)/Δt
εL=−LΔtΔI(17.31)
swipeε_L = −L ΔI/Δt (17.31)
orL=ΔI/Δt−εL(17.32)
swipeor L = −ε_L/(ΔI/Δt) (17.32)
Here L is self-inductance of the coil and minus sign indicates that the induced emf opposes the applied voltage. In the above expression, If we take ε_L = 1 volt and ΔI/Δt = 1 A s⁻¹, then L = 1 henry (H), defined as:
The self-inductance of the coil can also be defined as ratio of the emf to the rate of change of current in the same coil. The SI unit of self-inductance L is Vs A⁻¹ having dimensions [ML²T⁻²A⁻²].
By equating Eqs.17.30 and 17.31, we have
−NΔtΔϕ=−LΔtΔI
swipe−N Δφ/Δt = −L ΔI/Δt
L=NΔIΔϕ(17.33)
swipeL = N Δφ/ΔI (17.33)
which gives another form of equation for self-inductance of the coil.
Example 17.8
A coil has an inductance reactance of 160 Ω at a frequency of 50 Hz. Calculate self-inductance of the coil.
where ε_L is the magnitude of self-induced emf and is given by
εL=LΔtΔI
swipeε_L = L ΔI/Δt
So, putting values in Eq.17.34, we have
W=ΔqLΔtΔI=ΔtΔqLΔI(17.35)
swipeW = Δq L ΔI/Δt = (Δq/Δt) L ΔI (17.35)
where Δq/Δt represents average current and is given by
ΔtΔq=(20+I)=21I
swipeΔq/Δt = ((0+I)/2) = ½I
AndΔI=I−0=I
swipeAnd ΔI = I − 0 = I
Putting the values in Eq.17.35, we have
W=(21I)LI=21LI2(17.36)
swipeW = (½I)LI = ½LI² (17.36)
This work is stored as potential energy in the inductor. Hence,
Um=21LI2(17.37)
swipeUₘ = ½LI² (17.37)
It is to be noted that in an inductor, energy is stored in the magnetic field and can never be negative because it is proportional to square of current. The inductor stores energy while absorbing power, returns the previous stored energy when delivering power, so the net energy transfer can never be negative. Using the Eq.17.37 expressed in terms of magnetic field B of solenoid can be found having:
n = number of turns per unit length
A = Area of cross section of coil
B = Magnetic field strength = μₒnI (Negative field due to solenoid)
I = current in solenoid = B/μₒn
L = Self Inductance = μₒn²Al where l is the length of solenoid
Putting the values in Eq.17.37 we have
Um=21μon2Al(μonB)2
swipeUₘ = ½ μₒn²Al (B/μₒn)²
Um=2μoB2(Al)
swipeUₘ = (B²/2μₒ)(Al)
As Al=volume, soUm=B22μo1(volume)
swipeAs Al = volume, so Uₘ = B² (1/2μₒ)(volume)
orvolumeUm=μo1B2
swipeor Uₘ/volume = (1/μₒ)B²
The energy stored Uₘ, per unit volume inside the solenoid is called energy density, and for an inductor it is given by
where Nₛ is the number of turns in the secondary coil.
Let φₛ represents flux passing through the secondary coil. The net flux passing through the secondary coil of Nₛ loops is Nₛφₛ. As this net flux is proportional to the magnetic field produced by the current Iₚ in the primary and the magnetic field itself is proportional to Iₚ, therefore
Nsϕs∝Ip
swipeNₛφₛ ∝ Iₚ
Nsϕs=MIp(17.40)
swipeNₛφₛ = MIₚ (17.40)
where M is proportionality constant and is called Mutual inductance of the two coils, given by
M=NsIpϕs
swipeM = Nₛ φₛ/Iₚ
The mutual inductance M depends upon the following factors,
Number of turns of both the primary and secondary coils.
Area of cross-section of the two coils.
Magnetic permeability of medium between the coils.
Nature of material on which two coils are wound.
Distance between two coils.
Orientation between the primary and secondary coils.
By Faraday's law, the emf in the secondary coil is given by the rate of change of flux through the secondary coil as:
εs=−NΔtΔϕs
swipeεₛ = −N Δφₛ/Δt
Using Eq. (17.40), we have:
εs=−ΔtΔNsϕs
swipeεₛ = −ΔNₛφₛ/Δt
εs=−ΔtΔMIp
swipeεₛ = −ΔMIₚ/Δt
εs=−MΔtΔIp(17.41)
swipeεₛ = −M ΔIₚ/Δt (17.41)
Which shows that emf induced in the secondary coil is proportional to time rate of change of current in the primary. The negative sign indicates the fact that the induced emf is in such a direction that it opposes the change of current in the primary coil. The magnitude of mutual induction M is
M=ΔIp/ΔtEs(17.42)
swipeM = Eₛ/(ΔIₚ/Δt) (17.42)
Brain teaser: a pacemaker with its leads in the right atrium and right ventricle (original drawing after the textbook's picture).
The SI unit of mutual inductance M is V s A⁻¹, which is called henry after Joseph Henry. One henry is the mutual inductance of the pair of coils in which the rate of change of current of one ampere per second in the primary causes an induced emf of one volt in the secondary.
Mutual inductance finds many applications in various devices such as transformers, electric motors, and generators etc. It also plays a key role in digital signal processing and is utilized in devices like pacemakers and metal detectors.
where Iₐᵥ and Vₐᵥ represent average value of alternating current and alternating voltage respectively whereas Iₒ and Vₒ represents maximum or peak values of alternating current and voltage respectively (Fig.17.3).
Figure 17.3: Graphically showing the rms value, average or mean value, peak value, and p-p value of alternating quantities-voltage (original drawing after the textbook's Figure 17.3).
Instantaneous Value: The value of an AC quantity at any instant of time is known as instantaneous value. The value of instantaneous voltage is given as:
V=Vosin(ωt)
swipeV = Vₒ sin (ωt)
Asω=T2π
swipeAs ω = 2π/T
therefore,V=VosinT2πt
swipetherefore, V = Vₒ sin (2π/T) t
Alsof=T1
swipeAlso f = 1/T
SoV=Vosin(2πft)
swipeSo V = Vₒ sin (2πft)
The value of instantaneous current is:
I=Iosin(ωt)
swipeI = Iₒ sin (ωt)
orI=Iosin(2πft)(17.2)
swipeor I = Iₒ sin (2πft) (17.2)
Peak or Maximum Value: It is the highest value that an AC waveform reaches during one cycle. It is the topmost point on the positive half-cycle or the bottommost point on the negative half-cycle (Figs.17.1 and 17.2). It is written by Vₒ and Iₒ for voltage and current respectively.
Peak to Peak Value: This is the total distance from the positive peak to the negative peak of the waveform. For a symmetrical sine wave:
Vp-p=2×Vo
swipeVₚ₋ₚ = 2 × Vₒ
The p-p value of the voltage waveform shown in Fig.17.2 is 2 Vₒ.
If L is the inductance of the coil, then changing current sets up a back emf in the coil of magnitude:
V=LΔtΔI
swipeV = L ΔI/Δt
To maintain a constant current, the applied voltage must be equal to the back emf. The magnitude of applied voltage across the coil must have value given by
AsI=Iosinωt,so
swipeAs I = Iₒ sin ωt, so
V=LΔtΔ(Iosinωt)
swipeV = L (Δ/Δt)(Iₒ sin ωt)
V=LIoΔtΔsinωt(7.14)
swipeV = LIₒ (Δ/Δt) sin ωt (7.14)
AsΔtΔsin(ωt)=ωcos(ωt),therefore,
swipeAs (Δ/Δt) sin(ωt) = ω cos(ωt), therefore,
V=ωLIocos(ωt)
swipeV = ωLIₒ cos(ωt)
AsωLIo=Vo,so
swipeAs ωLIₒ = Vₒ, so
V=Vocos(ωt)
swipeV = Vₒ cos(ωt)
Ascosωt=sin(ωt+2π),so
swipeAs cos ωt = sin (ωt + π/2), so
V=Vosin(ωt+2π)(17.15)
swipeV = Vₒ sin (ωt + π/2) (17.15)
Figure 17.7: (a) Inductor L is connected with an AC source; (b) graphically showing voltage is leading current in an inductor; (c) vector representation of V and I in an inductor (original drawing after the textbook's Figure 17.7).
It is seen from Eq.17.15, the voltage across the inductor L is leading the current, or in other words, current is lagging behind the voltage in AC circuit containing an inductor as shown graphically in Figs.17.7(b) and 17.7 (c). The current in an inductor always lags behind the voltage by 90° or π/2 rad. The resistance offered by an inductor is called inductive reactance denoted by X_L and is given as
XL=IrmsVrms(17.16)
swipeX_L = Vᵣₘₛ/Iᵣₘₛ (17.16)
where Vᵣₘₛ is the rms value of alternating voltage in the inductor and Iᵣₘₛ is the rms current passing through it.
AsVrms=0.707VoandIrms=0.707Io,so
swipeAs Vᵣₘₛ = 0.707 Vₒ and Iᵣₘₛ = 0.707 Iₒ, so
XL=0.707Io0.707Vo=IoVo
swipeX_L = 0.707Vₒ/0.707Iₒ = Vₒ/Iₒ
AsVo=ωLIo,soXL=IoωLIo
swipeAs Vₒ = ωLIₒ, so X_L = ωLIₒ/Iₒ
HenceXL=ωL=2πfL(17.17)
swipeHence X_L = ωL = 2πfL (17.17)
It shows that inductive reactance X_L is directly proportional to both, frequency of current and the inductance L of the inductor. In case of DC, f = 0, so X_L = 0, while in case of large AC frequency, X_L is also large. Thus, we conclude that an inductor allows DC but blocks the AC. The unit of X_L is ohm.
Our heart is driven by electric pulses; the high electric frequency of AC current can affect the frequency of the heart and can lead to a heart attack.
The maximum ripple voltage present in a full-wave rectifier bridge circuit is not determined by the value of the smoothing capacitor but by the frequency and load current, and is calculated as:
Vripple=frippleCIDCorVripple=2fCIDC
swipeV_ripple = I_DC/(f_ripple C) or V_ripple = I_DC/(2fC)
where I_DC is the load current in ampere, f is input frequency and C is capacitance in farad (F). It is to be noted that ripple frequency f_ripple is twice that of the input frequency,
where V represents magnitude of alternating current or voltage corresponding to time t, Vₒ represents maximum value of voltage and ω is the angular frequency of alternating voltage as shown in Fig 17.1. We can write Eq. 17.1 for current as:
I=Iosinωt
swipeI = Iₒ sin ωt
where I is instantaneous value of alternating current at time t, Iₒ is its maximum or peak value ω is its angular frequency.
Figure 17.1: Waveform of alternating voltage (original drawing after the textbook's Figure 17.1).
In case of current, the direction of current reverses after every half-cycle and in case of voltages, the polarity of potential difference reverses after every half cycle. The second condition to be an alternating one is that amplitude or the peak value of current or voltage i.e., the maximum value on both positive and negative sides remains constant in all cycles but changes occur most rapidly at the zero (crossover) points and most slowly at its peak (Fig. 17.1).
Some important terms related to alternating quantities are:
Waveform: The path traced by an alternating quantity, such as the voltage in Fig.17.1 plotted as a function of some variable such as time.
Cycle: One complete set of positive and negative values of an alternating quantity is called a cycle. Figure 17.1 shows one cycle of an alternating voltage.
Time period (T): The time taken to complete one cycle of an alternating quantity is called its time period and is measured in seconds.
Frequency (f): The number of cycles that occur in one second is called its frequency. The unit of frequency is hertz (Hz); where 1 Hz = 1 cycle per second and f = 1 / T.
Figure 17.10: (a) RL series circuit connected with A.C. supply; (b) voltage and current waveform of RL series circuit; (c) vector diagram of VR and VL of RL series circuit (original drawing after the textbook's Figure 17.10).
Let rms value of current through R is I. Then rms value of voltage V_R across R will be:
VR=IrmsR
swipeV_R = IᵣₘₛR
V will be in phase with the current I in the circuit, as R is shown vectorially by line OA in Fig.17.10(c). The value of rms voltage V_L across L will be:
VL=IrmsXL
swipeV_L = IᵣₘₛX_L
For your information: an electric eel (original drawing after the picture printed in the textbook's box).
Voltage V across L is ahead of current I through L by 90° as shown in Fig.17.10 (b) and vectorially by line OB in Fig.17.10(c). The resultant voltage V will be the vector sum of V_R and V_L shown vectorially by line OP, thus in Fig.17.10(c):
Vrms=VR2+VL2
swipeVᵣₘₛ = √(V_R² + V_L²)
Vrms=(IrmsR2)+(IrmsXL2)
swipeVᵣₘₛ = √((IᵣₘₛR²) + (IᵣₘₛX_L²))
AsXL=ωL,soVrms=IrmsR2+(ωL)2
swipeAs X_L = ωL, so Vᵣₘₛ = Iᵣₘₛ √(R² + (ωL)²)
ImpedanceZ=IrmsVrms=R2+(ωL)2(17.23)
swipeImpedance Z = Vᵣₘₛ/Iᵣₘₛ = √(R² + (ωL)²) (17.23)
Angleθ=tan−1(RωL)
swipeAngle θ = tan⁻¹(ωL/R)
The angle θ which Z makes with R line, gives the phase difference between the applied voltage and current.
which correspond to Figs.17.5(b) and 17.5(c) respectively, the initial phase of both voltage V and current I is zero. There are situations when current I and voltage V are not in phase i.e; they differ in phase. For example, the initial phase of current I may be positive or negative as compared to the initial phase of voltage V, which is zero. Consider a situation in which the initial phase of voltage V is zero and initial phase of current I is φ as shown in Fig.17.5 (b). This situation can be represented by the following equations:
V=VosinθandI=Iosin(θ+ϕ)
swipeV = Vₒ sin θ and I = Iₒ sin (θ + φ)
At t = 0; voltage V = 0, but the current is positive and I = Iₒ sin φ. It means that the current had its zero value earlier by an angle φ than voltage. Thus, we can say that the current is leading the voltage by an angle φ in this situation (Fig. 17.5-b). The angle φ is the phase difference between the voltage and the current.
Similarly, the initial phase of current I is negative as compared to the initial phase of voltage V, which is zero as shown in Fig.17.5(c). This situation can be represented by the following equations:
V=VosinθandI=Iosin(θ−ϕ)
swipeV = Vₒ sin θ and I = Iₒ sin (θ − φ)
It means the value of V is zero, but the current I has some negative value (I – sin φ). It means that the current I will reach its zero value later on by an angle φ than the voltage V. Thus, we can say that current I is lagging behind the voltage V by an angle φ. The angle φ is called the phase difference between V and I.
Figure 17.5 (b), (c): Graphical representation showing (b) current leads the voltage, (c) current lags behind voltage (original drawing after the textbook's Figure 17.5 (b), (c)).
The instantaneous current I through the circuit is:
I=RV
swipeI = V/R
Using Eq.17.10;I=RVosinωt
swipeUsing Eq.17.10; I = (Vₒ sin ωt)/R
I=Iosinωt(17.11)
swipeI = Iₒ sin ωt (17.11)
where Iₒ = Vₒ/R is the peak or maximum value of current.
Figure 17.6: (a) A resistor R connected with an AC source; (b) graph for a purely resistive circuit showing V and I in phase; (c) VR and IR vectors for a resistance (original drawing after the textbook's Figure 17.6).
It follows from Eqs.(17.10) and (17.11) that the instantaneous values of both voltage and current are sine functions which vary with time. Figure 17.6(b) shows that both voltage and current pass their minimum and maximum values at the same time and thus their instantaneous values are said to be in phase with each other.
Also Fig.17.6(c) shows V_R and I_R vectors for resistance. V and I are drawn parallel because there is no phase difference between them. The opposition to AC which the circuit presents is the resistance given by
R=IV
swipeR = V/I
For your information: a 12 V AC doorbell (original drawing after the photograph printed in the textbook's box).
The power dissipation is proportional to the square of the current and makes no difference whether the current is direct or alternating i.e., whether the sign associated with the current is positive or negative. However, the power dissipation produced by AC having maximum value Iₒ is not the same as that produced by a direct current of maximum value Iₒ, because the alternating current is at this maximum value only for an instant during each half-cycle. Instantaneous power P dissipated across a resistor in AC circuit is:
P=VIorP=I2RorP=RV2(17.12)
swipeP = VI or P = I²R or P = V²/R (17.12)
and average power
⟨P⟩=⟨I2R⟩
swipe<P> = <I²R>
As⟨I2⟩=2Io2=Irms2,so
swipeAs <I²> = Iₒ²/2 = Iᵣₘₛ², so
Average power⟨P⟩=2Io2R=Irms2R
swipeAverage power <P> = (Iₒ²/2)R = Iᵣₘₛ²R
Also, it can be proved that;
Average power⟨P⟩=IrmsVrms
swipeAverage power <P> = IᵣₘₛVᵣₘₛ
It is to be noted that here P is measured in watts V in volts, I in amperes and R in ohms respectively, and the Eq.(17.12) for power holds good only when V and I are in phase.
Example 17.3
A 1 kW heating element is connected to a 250 V AC supply voltage. Calculate the amount of current taken from the supply and the resistance of the element when it is hot.
Figure 17.5 (a): AC cycle corresponds to a phase (original drawing after the textbook's Figure 17.5 (a)).
The angle which gives the value of alternating quantity is known as phase.
The phase of points A, B, C, D and E are 0, π/2, π, 3π/2 and 2π respectively as shown in Fig.17.5(a), Thus each point of A.C cycle corresponds to a phase.
The rms value of an alternating voltage is defined as:
The value of a constant voltage that produces the same power in a resistor as the alternating voltage.
Vrms=2VoorVrms=0.707Vo(17.4)
swipeVᵣₘₛ = Vₒ/√2 or Vᵣₘₛ = 0.707 Vₒ (17.4)
where Iₒ = Peak or maximum current
Vₒ = Peak or maximum voltage
So, rms current, Iᵣₘₛ is equal to 0.707 Iₒ, which is about 70% of the peak current Iₒ.
Example 17.1
The steady direct current, or voltage that delivers the same average power in a resistor as the alternating current, or voltage. Using the graph as shown in the figure and the equation for alternating current, calculate the value of the current at a time 0.67 s.
Solution
We know that for AC circuits;
I = Iₒ sin (ωt) and ω = 2π/T
The time period T is the time taken for one full cycle, and peak current Iₒ from the graph are:
T = 0.10 s and Iₒ = 17 A
Using the equation I = Iₒ sin (ωt)
As ω = 2π/T, therefore, I = Iₒ sin (2π/T) t
I = 17A × sin (2 × 3.14 × 0.67s / 0.1 s)
I = 17A × sin 42°
I = 17A × (0.917) = 15.58A
Graph for Example 17.1: current against time (original drawing after the textbook's graph in Example 17.1).
2.Current: At resonance, the current in the circuit reaches its maximum value due to the minimum impedance (Fig. 17.11-d).
3.Phase Angle: At resonance, the phase angle is zero, indicating that the voltage and current are in phase and have power factor equal to 1.
Figure 17.11 (e): On a car, the shock absorber damps motion and dissipates energy. This is much like the resistance in an RLC-circuit. The mass and spring determine the resonant frequency (original drawing after the textbook's Figure 17.11 (e)).
4.Damping: The resistor in the circuit introduces damping, which affects the oscillations of the current. A higher resistance leads to more damping, causing the oscillations to decay faster. The forced but damped motion of the wheel on the car spring is analogous to an RLC-series AC circuit. The shock absorber damps the motion and dissipates energy, analogous to the resistance in an RLC-series circuit. The mass and spring determine the resonant frequency as shown in Fig.17.11(e).
5.Tuning and Filtering: RLC-series circuits, especially at resonance, are widely used for tuning in radio receivers and other communication devices. They can be used as band-pass filters, allowing signals within a specific frequency range to pass while attenuating others.
6.Voltage Amplification: At resonance, the voltage across the inductor and capacitor can be significantly higher than the applied voltage due to the circulating current. This phenomenon is known as voltage amplification.
7.Power Dissipation: The power dissipation in RLC-series circuit is given by
P=VIcosθ(17.27)
swipeP = VI cos θ (17.27)
which is known as a true power in RLC-series circuit and it shows that a maximum power will be dissipated when θ = 0, which is only possible in resistor. However, the power dissipation in impedance is called apparent power and is equal to VI cosθ.
Example 17.7
In a LCR-circuit, an inductor having inductive voltage 20 V, capacitor with capacitive voltage 11 V and a resistance with voltage 12 V are connected in series. Find phase difference between resultant voltage and current in the circuit. Also calculate the Vᵣₘₛ value of voltage of AC source.
Solution
V_L = 20 V, V_C = 11 V and V_R = 12 V
We know that; Phase difference for RLC-series circuit is given by
tan θ = (V_L − V_C)/V_R
tan θ = (20 V − 11 V)/12 V = 0.75
or θ = tan⁻¹ (0.75) = 36.8°
Also we know that;
Vᵣₘₛ = √((V_R)² + (V_L − V_C)²)
Vᵣₘₛ = √((12 V)² + (20 V − 11 V)²)
Vᵣₘₛ = √(144 V² + 81 V²)
Vᵣₘₛ = √(225 V²) = 15 V
Example 17.7: phasors V_L, V_C and V_R (original drawing after the textbook's sketch).
Example 17.7: V_R, V_L − V_C and the resultant V_rms (original drawing after the textbook's sketch).
Figure 17.12 (a), (b): (a) RLC-parallel circuit connected with an AC source; (b) a graph showing resonance frequency with its resonance current Ir (original drawing after the textbook's Figure 17.12 (a), (b)).
2.Voltage and Current: In a RLC-parallel circuit, the voltage is same across all components, so for convenience, the voltage may be taken as a reference phasor. At the resonance, current is minimum but it can be significantly magnified, while the source current remains relatively low. So, it may be used for current magnification. The variation of current with frequency of the source is shown in Fig.17.12 (b). At resonance, the branch currents IL and IC may each be larger than the resonance current Iᵣ.
3.Admittance: Admittance (Y) is the reciprocal of impedance and is used to analyze parallel circuits. The total admittance of a parallel RLC-circuit is the sum of the admittances of the individual components.
4.Frequency and Bandwidth: The impedance, admittance, and currents in a parallel RLC-circuit are all frequency-dependent. The bandwidth of a parallel RLC-circuit is the range of frequencies over which the circuit operates effectively. The resonance frequency of RLC-parallel circuit is:
fr=2πLC1
swipefᵣ = 1/(2π√LC)
Figure 17.12 (c): RLC-parallel circuits-a core principle behind induction cooktops (original drawing after the photograph printed as the textbook's Figure 17.12 (c)).
Do you know?: an electrocardiogram (ECG) (original drawing after the picture printed in the textbook's box).
The parallel RLC-circuit can also be used for tuning circuits, signal processing, and power systems. RLC-parallel circuits are indeed used in induction cooktops to match the desired heating frequency, specifically, the resonant behaviour of a parallel RLC-circuit is important for the operation of induction heating, which is the core principle behind induction cooktops i.e; the RLC-parallel circuit generates a high frequency current in the coil, which induces currents in the metal cookware, causing it to heat up as shown in Fig. 17.12(c).
5.Quality Factor (Q): The quality factor is a measure of the sharpness of the resonance peak and indicates how much energy is stored in the circuit compared to the energy dissipated. In a parallel RLC-circuit, the Q-factor is inversely proportional to the resistance.
6.Power Factor: The power factor in a parallel RLC-circuit can vary depending on the frequency and the relative magnitudes of the inductive and capacitive reactances. At resonance, the power factor is unity.
The charge on the capacitor at any instant is given by
q=CV=CVosinωt
swipeq = CV = CVₒ sin ωt
ThusI=ΔtΔq=ΔtΔ(CVosinωt)
swipeThus I = Δq/Δt = (Δ/Δt)(CVₒ sin ωt)
I=CVoΔtΔ(sinωt)
swipeI = CVₒ (Δ/Δt)(sin ωt)
AsΔtΔsinωt=ωcosωt,thus
swipeAs (Δ/Δt) sin ωt = ω cos ωt, thus
I=CVoωcosωt
swipeI = CVₒω cos ωt
Ascos(ωt)=sin(ωt+2π),so
swipeAs cos(ωt) = sin (ωt + π/2), so
I=ωCVosin(ωt+2π)
swipeI = ωCVₒ sin (ωt + π/2)
I=ωCVosin(ωt+2π)
swipeI = ωCVₒ sin (ωt + π/2)
HereωCVo=Io,thus
swipeHere ωCVₒ = Iₒ, thus
I=Iosin(ωt+2π)(17.19)
swipeI = Iₒ sin (ωt + π/2) (17.19)
Equations 17.18 and 17.19 show that inductor current I leads the voltage by 90° or π/2 rad or voltage lags behind the current I by 90° or π/2 rad as shown in Figs.17.8(b) and .17.8(c).
Resistance offered by capacitor is known as capacitive reactance denoted by X_C and is given by
XC=IrmsVrms
swipeX_C = Vᵣₘₛ/Iᵣₘₛ
where Vᵣₘₛ is the rms value of alternating voltage in the inductor and Iᵣₘₛ is the rms current passes through it.
AsVrms=0.707VoandIrms=0.707Io,so
swipeAs Vᵣₘₛ = 0.707Vₒ and Iᵣₘₛ = 0.707Iₒ, so
XC=0.707Io0.707Vo=IoVo
swipeX_C = 0.707Vₒ/0.707Iₒ = Vₒ/Iₒ
AsIo=ωCVo
swipeAs Iₒ = ωCVₒ
HenceXC=ωC1=2πfC1where ω=2πf
swipeHence X_C = 1/ωC = 1/2πfC where ω = 2πf
The unit of capacitive reactance X_C is ohm and is given as:
XC=ωC1=2πfC1
swipeX_C = 1/ωC = 1/2πfC
Which shows that for low frequencies, capacitor will have a large reactance X_C and current I will be small whereas at high frequencies reactance X_C will be small and current I through the same capacitor will be large.