Lab Safety and Practical SkillsLab Safety and Practical Skills
Practical chemistry: general laboratory rules, physical/chemical/biological hazards with GHS pictograms, chemical waste disposal and first aid, then a full acid-base titration procedure with observation table and molarity equation, and qualitative salt analysis tables for anions (carbonate, halides, nitrate, sulphate) and cations (Al3+, NH4+, Ca2+, Cr3+, Cu2+, Fe2+, Fe3+, Zn2+) using NaOH and aqueous ammonia.
16.2.2 Chemical Hazards · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
Figure 16.2: Pictogram of chemical hazards (original drawing after the textbook's Figure 16.2).
A laboratory worker must use the chemicals according to the standard procedures keeping in view the particular hazards and precautions required for the safe use.
16.2.1 Physical Hazards · Reviewed lesson · version 1 · published 16 Nov 2026
The most common physical hazards are slips and falls when working on wet floor. A worker must take all types of precautions to avoid accidents related to physical hazards such as slipping, pulling, falling etc.
A worker should wear cut-resistant gloves while handling the broken glassware to prevent cuts, abrasions and skin damage. It should be mandatory for the laboratory staff to dispose off broken glassware in special container to prevent injury.
Procedure of Titration · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 0.1 MB
i.Rinse the pipette first with distilled water and then with the given NaOH solution.
ii.Rinse the conical flask with distilled water only.
iii.Pipette out 10 cm³ of NaOH solution into a conical flask.
iv.Add one to two drops of phenolphthalein indicator into it. The solution turns pink.
v.Rinse the burette first with distilled water and then with the given HCl solution.
vi.Fix the burette on a clamp stand in an upright position.
vii.Fill it with the given HCl solution with the help of a funnel. Remove funnel from the burette.
viii.Using the tap at the base of the burette, allow the acid to flow into a beaker to remove any air bubble present in the nozzle.
ix.Note the burette reading as an initial reading using an anti-parallax card or a white paper.
x.During titration, place the conical flask on a white paper under the burette to see the color change of the indicator clearly. Check that the burette does not leak.
xi.Carry out a rough titration by adding hydrochloric acid solution from the burette drop wise to the conical flask.
16.4 First aid in laboratory
16.4 First Aid in Laboratory · Reviewed lesson · version 1 · published 16 Nov 2026
Every laboratory must have a first aid box. Common accidents and their first aid treatments are given in the Table 16.1 below:
Table 16.1 Accidents and their First Aid treatment
Type of Accident
First Aid Treatment
1 Cuts
Minor cuts
Remove the glass piece if any, apply a little methylated spirit or tincture iodine with a piece of cotton. Both act as disinfectant.
Serious cuts
Apply pressure on the cut for about 10 minutes to stop bleeding. Consult a doctor.
2 Eye Injuries
Acid in the eye
16.5 Acid-base titration
16.5 Acid-Base Titration · Reviewed lesson · version 1 · published 16 Nov 2026
Volumetric analysis is used to find the concentrations of solutions by means of a technique known as titration. In this technique a solution of unknown concentration is combined slowly and carefully with a known volume of a standard solution until a colour change shows the completion of the reaction.
Either solution can be taken in a burette with the other solution taken in a conical or a titration flask.
16.3 Waste Disposal System for Chemicals · Reviewed lesson · version 1 · published 16 Nov 2026
Chemical waste cannot be disposed of in bins or sewer system. Most chemical wastes must be disposed of keeping in view the following rules and regulation of Environmental Protection Agency (EPA).
Store chemical wastes in proper containers.
Label the chemical waste containers with the types of wastes, the date of waste and place of origin.
These containers are then transferred to the allocated site where these are appropriately treated to dispose them off.
i.Chemical treatment of wastes involves neutralization, precipitation, ion exchange, oxidation or reduction.
c) Identification of Nitrate (NO₃¹⁻) radical · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 93 KB
Identification of nitrate radical
Experiment
Observation
Inference
Take 2 g of solid sample in a clean test tube and dissolve it in 5 cm³ distilled water. Add to it 5 cm³ of sodium hydroxide solution. Finally add 3 g of powdered aluminium metal.
A characteristic smell of NH₃ gas is felt near the mouth of test tube. This gas turns red litmus paper blue.
NO₃¹⁻ ions are indicated.
swipe
Nitrate test (original drawing after the figure printed in the textbook).
Aluminium metal reduces nitrate ions to ammonium ions which then react with aqueous NaOH to evolve ammonia gas. The reduction of NO₃¹⁻ with aluminium metal is a redox reaction in which Al metal
(d) Identification of Sulphate (SO₄²⁻) radical
(d) Identification of Sulphate (SO₄²⁻) radical · Reviewed lesson · version 1 · published 16 Nov 2026
Identification of sulphate radical
Experiment
Observation
Inference
Take 3 g of solid sample in a clean test tube. Dissolve it in 5 cm³ of distilled water. Acidify the solution with a few drops of dil. HNO₃ and then add 5 cm³ barium nitrate solution.
(b) Identification of chloride (Cl¹⁻), Bromide (Br¹⁻) and Iodide (I¹⁻) radicals
(b) Identification of chloride (Cl¹⁻), Bromide (Br¹⁻) and Iodide (I¹⁻) radicals · Reviewed lesson · version 1 · published 16 Nov 2026
Images and handouts: 63 KB
Identification of chloride, bromide and iodide radicals
Experiment
Observation
Inference
Take 2 g of solid sample in a test tube and add 5 cm³ of distilled water to make the aqueous solution. Add a few drops of dil. HNO₃ solution to acidify the solution of the salt, finally add about 5 cm³ of aqueous AgNO₃.
A thick white precipitate is formed which dissolves in aq.NH₃.
Cl⁻¹ ions are indicated.
Take 2 g of solid sample in a test tube and add 5 cm³ of distilled water to dissolve the salt. Add a few drops of dil. HNO₃ to acidify the above solution. Finally add 5 cm³ of aqueous AgNO₃.
A thick cream-yellow precipitate is formed.
Br¹⁻ ions are indicated.
Chemical Equation
Chemical Equation · Reviewed lesson · version 1 · published 16 Nov 2026
NaOHX(aq)+HClX(aq)NaClX(aq)+HX2OX(l)
swipeNaOH(aq) + HCl(aq) → NaCl(aq) + H₂O(l)
16.7 Tests for identification of basic radicals
16.7 Tests for Identification of Basic Radicals · Reviewed lesson · version 1 · published 16 Nov 2026
a) Identification of Aluminium (Al³⁺) radical
Take 4 g of solid sample in a clean test tube. Dissolve it in about 10 cm³ distilled water. Divide this solution into two parts for further tests.
Identification of aluminium radical
Experiment
Observation
Inference
To one part, add about 5 cm³ NaOH solution.
A white gelatinous precipitate is formed.
Al³⁺ ions are indicated.
To the second part of the above solution, add a few drops of aqueous ammonia.
16.6 Tests for Identification of Anions · Reviewed lesson · version 1 · published 16 Nov 2026
a) Identification of carbonate CO₃²⁻ radical
Identification of carbonate radical
Experiment
Observation
Inference
Take about 2 g of solid carbonate sample in a clean test tube and then add about 5 cm³ of dilute HCl solution. Pass the gas evolved in the above step through a solution of lime water.
Effervescence takes place during which a gas evolves briskly, that turns lime water turns milky.
xii.The contents of the flask must be swirled adding of acid for thorough mixing.
xiii.Keep on adding acid till the colour of solution becomes light pink persistently. This will be the end point of the reaction.
Again, note down the burette reading, this will be the final reading. The difference of final and initial readings of burette will give the volume of the acid used.
Figure 16.6: Procedure of titration (original drawing after the textbook's Figure 16.6).
Repeat the titration to get accurate and concordant readings. Take at least three concordant readings which agree with one another within 0.1 cm³.
Wash thoroughly with water and then with 1% sodium bicarbonate solution.
Alkali in the eye
Wash with water followed by 1% boric acid solution.
Foreign particle in the eye
Do not rub the eyes. Remove the particle carefully with soft handkerchief then wash with water.
Soreness in the eye
Put a drop of olive oil in the eyes and keep them closed for some time.
3 Burns
Burns with dry heat (flame, hot object); Burns causing blisters; Acid burns; Alkali burns; Bromine burns
• Apply burnol or mustard oil. • Wash freely with ice cold water. Then wash with a saturated solution of sodium bicarbonate and again with water. • Wash freely with water and then with 1% acetic acid solution and again with water, dry the skin and apply the burnol. • Wash fully with 2% ammonia solution and apply glycerin. Wipe off glycerin after sometime and apply burnol.
4 Poisons
Poisons swallowed
Spit immediately, wash mouth with water repeatedly.
Acid swallowed
Drink a lot of water or lime water or milk of magnesia.
Caustic alkalies swallowed
Drink a lot of water; drink a glass of lemon or orange juice.
Salt of heavy metals swallowed.
Take milk or white part of the egg.
5 Fire
i) Clothes catch fire
Do not run. Wrap with blanket or with dry cotton cloth. Lie down on the floor.
A chemistry laboratory is a chemist workshop. It is a place where a student is trained to observe the physical and chemical characteristics of substances by following definite procedures. Before starting the laboratory work, a student should get himself familiarized with the layout of the laboratory and various fittings provided on the laboratory table as well as the side shelves.
i.Students are expected to conduct themselves in a responsible manner at all times in the lab.
ii.They are advised not to work alone in the lab. Experiments should be performed in the presence of lab instructor and other laboratory staff.
iii.Students should always wear lab coat and safety goggles while working in the lab. Girls must tie up their scarves and hair before start working in the lab.
iv.Determine the potential hazards related to any equipment or the experiment before beginning any work. Appropriate safety precautions must be observed at all cost.
v.There must not be any crowding in the lab and students should stick to their work places at a safe distance from each other.
vi.Don’t bring any food items in the lab. Never taste or smell any compound or a gas.
vii.Any accident or breakage of glassware must be reported to the incharge of the laboratory immediately.
viii.If you cannot handle an instrument or an equipment properly then you must seek help from the instructor.
ix.Do not pour chemicals down the drains and do not utilize the sewer for chemical waste disposal.